Updated November 2026

Wren birdhouse plans PDF files give you a printable cut list, dimensions and assembly order for a small nest box that house wrens and Carolina wrens will readily use. In this guide you will get the core measurements, the materials to buy, and the build sequence that produces a box that stays dry, drains well and is easy to clean at the end of the season.

Dimensions and Materials for a Wren House

Most wren houses are built to a footprint of about 4 by 4 inches with a floor height of roughly 6 to 8 inches, and an overall height near 9 to 10 inches including the roof. Wrens prefer cavities that are dark and snug, so keep the interior compact. Use a 1-inch-thick board such as cedar, pine or cypress, because untreated softwood holds up to weather and does not need paint or stain on the inside.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

A typical cut list for a single-chamber design looks like this:

  • Front panel: 4 1/2 x 8 inches, with the entry hole drilled 6 inches above the floor
  • Back panel: 4 1/2 x 9 inches, extended slightly to support the roof
  • Two side panels: 4 x 8 inches each
  • Floor: 4 x 4 inches, with 1/4-inch drain holes at each corner
  • Roof: 5 x 6 inches, sloped and overhanging the front by about 1 inch

Confirm these numbers against the specific PDF you are following, since slight variations in width and height are common among published designs.

Cutting and Drilling the Parts

Start by cutting all panels to length on a miter saw or with a hand saw and a square. Mark the entry hole on the front panel with a compass set to 1 1/8 inches radius, which gives you a 1 1/4-inch opening. Drill a pilot hole first, then finish the circle with a spade or hole saw. A smaller 1 1/8-inch hole also works for wrens and keeps out larger competitors such as sparrows.

Drill drain holes in the floor and ventilation holes near the top of both side panels. Rough edges around the entry hole can be eased with a few light passes of sandpaper so the wrens are not scratched while entering.

Assembly and Finishing Steps

  1. Glue and screw the floor between the two side panels, keeping edges flush.
  2. Attach the back panel with exterior wood glue and 1 1/4-inch galvanized or stainless screws.
  3. Fix the front panel last, leaving it slightly proud at the top so the roof sits cleanly.
  4. Attach the roof with hinges or screws through cleats, so you can open it for cleaning each fall.
  5. Seal exterior faces with a non-toxic exterior finish only if you choose, and leave the interior bare.

Pre-drill every screw hole near edges to prevent splitting. Clamp parts while the glue sets, and let the assembly cure overnight before mounting.

Mounting the Box Where Wrens Will Use It

Mount the box 5 to 10 feet off the ground on a post, fence or tree in partial shade, with the entry facing away from prevailing winds. Avoid placing it near feeders, since busier birds can crowd out wrens. Many guides also recommend a guard or baffle on posts to deter raccoons and cats.

Common Mistakes

  • Entry holes larger than 1 1/4 inches, which invite starlings and sparrows.
  • Skipping drain holes, which lets water collect and rot the floor.
  • Using pressure-treated or painted interiors that can harm nesting birds.
  • Mounting the box in full sun, which can overheat the chamber.
  • Cleaning out nests during the breeding season, which disturbs active birds.

A sharp spade bit or hole saw produces a clean entry hole with little tear-out, which matters on thin cedar. View on Amazon

Exterior wood glue combined with corrosion-resistant screws keeps seams tight through seasonal swelling and drying. View on Amazon

A combination square helps you lay out the entry hole, floor and panel edges accurately before cutting. View on Amazon

For more layouts with similar dimensions, see Plans for Wren Birdhouse: A Step-by-Step Guide With Cut List and Carolina Wren Birdhouse Plans: A Step-by-Step Build Guide. If you want a quicker project first, Popsicle Stick Birdhouse Plans PDF: Build a Simple Starter House is a useful warm-up.

FAQ

What size entry hole do wrens need?

A 1 1/8 to 1 1/4-inch entry hole suits house wrens and Carolina wrens while keeping out larger birds. Smaller holes also help exclude starlings and sparrows.

Should I paint the inside of a wren house?

No. Leave the interior unfinished so the wood stays free of paint fumes and residues that could affect nesting birds.

When should I clean out an old wren nest?

Clean the box in late fall or early winter, after the breeding season ends. Removing nests during active nesting can disrupt the birds.

Conclusion

With the right dimensions, a 1 1/8-inch entry hole and proper drainage, a wren house built from a PDF plan is a manageable weekend project. Mount it in partial shade away from feeders, and check it each season to keep it sound and clean.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.