Updated November 2026
Traffic light birdhouse plans describe a stacked, three-chamber nest box shaped like a signal post, with a separate compartment on each side. This guide gives you a cut list, hole sizing, and assembly steps for a sturdy version you can build in an afternoon. The design works well as a small-bird house, and the stacked compartments can host more than one pair of birds in a single season.
Plan the Dimensions Before You Cut
The traffic light design is a tall box divided into three internal rooms, one above the other, with a separate entry hole for each. Each room should be sized for the species you want. A 4-inch by 4-inch floor with 8 to 9 inches of interior height works for chickadees, wrens, and titmice. Keep the entry holes at 1-1/8 inches for chickadees and 1-1/4 inches for titmice or house wrens, and drill them about 6 inches above each floor.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
Use cedar, pine, or another rot-resistant softwood about 3/4 inch thick. Do not use pressure-treated lumber, because the chemicals can harm nesting birds. Leave the inside unfinished and unpainted.
Cut List and Materials
The following cut list builds one three-chamber house with a 4-inch square footprint. Cut all pieces from 3/4-inch stock, then dry-fit before fastening.
| Part | Qty | Dimensions (inches) |
|---|---|---|
| Front and back panels | 2 | 5-1/2 x 26 |
| Side panels | 2 | 3-1/2 x 26 |
| Internal floors (one per room) | 3 | 3-1/2 x 3-1/2 |
| Internal dividers | 2 | 3-1/2 x 8 |
| Roof panel | 1 | 6 x 6 |
| Mounting back | 1 | 5 x 26 |
You will also need exterior-grade wood glue, 1-1/4-inch exterior screws or galvanized nails, a 1-1/8-inch and a 1-1/4-inch hole saw or spade bit, and a drill.
Assembly Steps
Assemble the box in stages so each compartment is sealed before you move up to the next one.
- Drill the entry holes in the front panel, spacing them about 8 inches apart vertically so each room has its own door.
- Glue and screw the side panels to the back panel, leaving the front open at first.
- Attach the internal floor pieces at 8-inch intervals, then fasten the two dividers so they create three separate rooms.
- Drill 1/4-inch drainage holes in each floor, and drill a few 1/8-inch ventilation holes near the top of each room.
- Attach the front panel with screws so it can be removed for cleaning later.
- Fasten the roof panel with a slight overhang on all sides, and add a mounting bracket to the back.
Mounting and Placement
Mount the house 5 to 10 feet off the ground on a pole or a tree trunk, facing away from prevailing winds and direct afternoon sun. Each entry hole should face a clear flight path. Leave 20 to 30 feet between this house and any other nest box so the pairs don’t crowd each other. Clean out old nesting material each fall, and check the box for wear before the next breeding season.
Common Mistakes
- Using pressure-treated wood or painted interior surfaces, which can harm nestlings.
- Drilling entry holes that are too large, which lets predators or competing species in.
- Skipping drainage holes, which allows moisture to build up in the rooms.
- Mounting the house where a cat or raccoon can reach it easily.
- Building all three rooms as one open space, which defeats the purpose of the design.
For other small-bird designs with similar build steps, see Simple Cedar Birdhouse Plans: A Step-by-Step Build in One Weekend and Wren Birdhouse Plans Free: Build a Cedar House in One Weekend. If you prefer a single-chamber build, Red Cedar Birdhouse Plans: A Step-by-Step Build With Cut List covers a different approach.
Recommended Gear
- Hole saw kit for birdhouse entries: Gives you clean, round entry holes in exact sizes, which matters when you are cutting three different openings. View on Amazon
- Exterior wood glue: Holds the internal dividers firmly against moisture and temperature swings. View on Amazon
- Galvanized exterior screws: Resist rust and keep the joints tight over several seasons. View on Amazon
FAQ
What bird species are traffic light birdhouses best for?
Their small, separated compartments suit chickadees, titmice, and house wrens. Adjust the entry hole size for each species you want to attract.
Can I use reclaimed wood for this build?
Yes, as long as it is untreated, unpainted on the inside, and at least 3/4 inch thick. Check for old finishes or chemical residue before using it.
How often should I clean the nest boxes?
Clean out old nesting material once each fall after the birds have left. Doing so reduces parasites and prepares the rooms for the next season.
Conclusion
A traffic light birdhouse gives you three separate nesting rooms in a single compact box, and the plan above keeps the build manageable for a beginner. Confirm entry hole sizes for your local species before you drill, and place the house where predators can’t easily reach it. Consult a local wildlife or extension office if you are unsure which species nest in your area.
