Updated November 2026
Learning how to cut wood with a router comes down to three things: choosing the right bit, setting a shallow depth for each pass, and feeding the tool in the correct direction. Once you follow those steps, you can make straight, clean cuts for dadoes, rabbets and profiles without tearing the grain. This guide walks through the process from setup to finish.
Prepare the Router and Workpiece
Start by making sure the bit is seated correctly. Insert the shank so it bottoms out in the collet, then pull it back about 1/16 inch and tighten. A bit that is not fully seated can slip under load and ruin a cut.
Shopping for one? See our guide: 7 Best Router Bit to Cut Wood Options for Every Project (2026).
Next, clamp the workpiece firmly to a bench or sacrificial base. Keep clamps well away from the router’s path so the base never hits them.
Set the Depth and Make Shallow Passes
Never try to remove the full depth in one pass. For hardwood, many woodworkers cut in passes of about 1/4 inch or less, and go shallower with larger bits. Lower the bit gradually across several passes until you reach the final depth.
- Set the depth to about 1/8 inch and make one full pass along the line.
- Increase the depth by a similar amount and repeat until you reach the target depth.
- Leave a final light pass of about 1/32 inch for a smoother finish if the edge matters.
Feed in the Correct Direction
Feed direction controls safety and finish quality. Move the router counterclockwise around the outside of a workpiece, so the bit’s cutting edge meets the wood in the same direction the router is pushed. When you cut an inside edge, reverse the logic and still keep the bit rotating against the feed.
Feed at a steady pace. Too slow and the bit burns the wood; too fast and the motor bogs down or the cut tears out. Listen to the motor and watch the chips: a healthy cut produces clean, consistent shavings.
Use a Guide for Straight and Repeatable Cuts
For straight lines, clamp a straightedge or use a fence. For dadoes and grooves, a template or guide bushing gives you a consistent width. If you are cutting grooves or curves, the related guides on this site cover those setups in more detail, such as How to Cut Grooves in Wood with a Router: A Step-by-Step Guide and How to Cut Curves in Wood with a Router: A Step-by-Step Guide.
When you need a circular cut, a trammel or circle jig works best. How to Cut a Circle in Wood with Router: Step-by-Step Method (2026) shows the method in full.
Checklist Before You Cut
- Bit fully seated and tightened in the collet
- Workpiece clamped with clearance for the base
- Depth set for a shallow first pass
- Feed direction confirmed (counterclockwise on outside edges)
- Safety glasses and hearing protection on
Common Mistakes
- Taking the full depth in one pass, which overloads the motor and causes burning.
- Feeding against the rotation, which can kick the router back toward you.
- Skipping test cuts on scrap of the same species and thickness.
- Forgetting to check for loose clamps or a wobbling bit before starting.
- Rushing the feed, which leads to tearout and rough edges.
Recommended Gear
- Collet wrench set: Lets you tighten and loosen bits securely without slipping. View on Amazon
- Router edge guide: Keeps the base tracking straight along a board edge for consistent cuts. View on Amazon
- Clamps for routing: Hold the workpiece steady so the bit stays on your line. View on Amazon
FAQ
How deep should each router pass be?
For most hardwoods, keep each pass to about 1/4 inch or less. Smaller passes reduce strain on the motor and produce cleaner edges.
Which direction should I feed a router?
Feed so the bit rotates against the direction of travel. On an outside edge, that means moving the router counterclockwise around the piece.
Can I cut wood with a router without a table?
Yes. A handheld router with an edge guide or straightedge works well for straight cuts, grooves and many profiles. A router table is helpful for small or repetitive work but is not required.
Conclusion
To cut wood with a router, set a shallow depth, make several passes, and feed in the correct direction with a steady hand. Use guides and clamps to keep every cut accurate. Practice on scrap first, and your finished edges will improve quickly.
