Updated November 2026
Bullnosing wood with a router means rounding over a square edge so the top and side meet in a smooth, full curve. This guide shows you how to bullnose wood with a router safely, from picking the right bit to making the final pass, so your edges look finished and feel comfortable in hand.
Choose the Right Bit and Setup
A bullnose bit has a radius at the tip that cuts a full half-round profile. Many woodworkers use a bit with a radius between 1/8 inch and 1/2 inch, though a larger radius leaves a softer, more pronounced curve. For a full bullnose on stock thicker than 3/4 inch, a bit with a radius matching about half the board thickness works well. Choose a bit with a bearing guide if you want the router to follow a template or the edge of the board itself.
Shopping for one? See our guide: 5 Best Wood Router Prices: How Much Is a Wood Router? 5 Picks Compared.
Clamp the workpiece firmly to the bench so it cannot shift. Keep the cutting edge sharp, since a dull bit burns the wood and tears fibers at the end grain.
Set the Depth and Make the Cut
Work in passes rather than one deep cut. Set the bit to remove no more than about 1/8 inch per pass in hardwoods, and shallower in dense or figured wood. Routers spin fast, so the feed rate matters as much as the depth.
- Unplug the router and install the bullnose bit, tightening the collet fully.
- Set the bit height to take a light first pass, about 1/8 inch deep.
- Test the setting on a scrap piece of the same species and thickness.
- Rout the edge with the router moving from right to left against the rotation of the bit, which is the standard feed direction on a handheld router.
- Repeat passes, lowering the bit in small increments, until the full radius is formed.
Work with the Grain Direction
End grain and cross-grain areas are where tear-out happens. Start the cut on the end of the board and work toward the center when possible, so any breakout falls off the piece. On long edges, check the grain direction before cutting. If the bit must cut against the grain, reduce the depth per pass and slow your feed to limit tearing. Some woodworkers add a sacrificial backer board at the exit point to protect the final edge.
Watch for Tear-Out on Figured Wood
Curly maple, birch and other figured woods tear more easily. Use lighter passes and a fresh, sharp bit, and consider a climb-cut only on the final light pass, with extreme care, because climb cuts can pull the router forward.
Finish the Edge
After the final pass, sand the curve by hand or with a sanding block wrapped in fine-grit paper, typically 150 to 220 grit, to remove any router marks. Keep the sanding block flat across the curve so you do not flatten the profile. Then apply your finish of choice.
Common Mistakes
- Cutting too deep in one pass, which causes burning, tear-out and router kickback.
- Feeding the router in the wrong direction, which makes the bit grab and pull.
- Skipping a test cut on scrap, leaving you with a ruined edge on the project piece.
- Using a dull bit, which leaves scorch marks and rough surfaces.
- Letting the router base tilt, which creates an uneven radius on one side of the edge.
If you are new to routing, see How to Use Wood Router Tool: A Step-by-Step Guide for Beginners for general handling tips, and How to Round Wood Corners with Router: Step-by-Step Guide (2026) if you also need rounded corners on the same project. For choosing a suitable spindle speed for your bit diameter, Router Speed Chart Wood: How to Pick the Right RPM for Each Bit (2026) is a useful reference.
Recommended Gear
- Router with variable speed control: Adjustable speed helps you slow the bit for large-diameter bullnose cuts and reduce burning. View on Amazon
- Bullnose router bit with bearing guide: A bearing follows the board edge for consistent radius cuts. View on Amazon
- Edge sanding block: A shaped block helps you smooth the curve without flattening it. View on Amazon
FAQ
Can I bullnose wood without a router?
Yes. A rasp, spokeshave or sanding block can shape a rounded edge by hand, though the process takes longer and the curve may be less uniform. For methods without a router, see How to Round Edges of Wood Without a Router: 4 Simple Methods.
Which way should I feed the router?
Feed the router counterclockwise around the workpiece, moving against the bit’s rotation. This keeps the bit cutting into the wood and gives you control.
How much of the edge should one pass remove?
Keep each pass to about 1/8 inch deep in most hardwoods. Lighter passes reduce burning, tear-out and strain on the router.
Conclusion
To bullnose wood with a router, pick a bit that matches your board thickness, take light passes and work with the grain. A test cut on scrap and a careful final sanding will give you a clean, comfortable edge on every project.
