Updated November 2026

Birdhouse bench plans free of charge give you a simple garden seat with a nest box built into the backrest or the end panels. In a weekend, you can build a sturdy bench from dimensional cedar or pine, with two cavities sized for chickadees or wrens and a mounting frame that keeps the house level. This guide covers the cut list, the build sequence and the details that keep both the bench and the birds comfortable.

Plan Overview and Cut List

The design below uses 1×6 cedar for the seat and back, 2×4 cedar for the legs and stretchers, and 1×8 cedar for the nest box end panels. Cedar resists rot without finish, which matters because the bench will sit outdoors year-round. Dimensions are nominal; check your lumber before cutting.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

Part Qty Material Finished Size
Seat slats 5 1×6 cedar 3/4 x 5-1/2 x 36 in
Back slats 3 1×6 cedar 3/4 x 5-1/2 x 36 in
Front legs 2 2×4 cedar 1-1/2 x 3-1/2 x 17 in
Rear legs 2 2×4 cedar 1-1/2 x 3-1/2 x 22 in
Seat stretchers 2 2×4 cedar 1-1/2 x 3-1/2 x 32 in
Nest box sides 2 1×8 cedar 3/4 x 7-1/4 x 10 in
Nest box front/back 2 1×8 cedar 3/4 x 7-1/4 x 9 in

Step-by-Step Build Process

Cut all parts first and label the seat slats in order so the grain and color match. Next, assemble the legs and stretchers, then fasten the seat slats, and finally mount the nest box into the back assembly.

  1. Cut the legs and stretchers. Set your miter saw to 90 degrees for square ends. Mark the rear legs at a slight angle if you want the back to recline about 10 degrees.
  2. Join the frame. Pre-drill and use exterior-rated 2-1/2 inch deck screws. Two screws per joint is the minimum; three is better for the stretchers.
  3. Attach the seat slats. Space them with a 1/4 inch spacer, which lets rain drain and prevents trapping water.
  4. Build the nest box. Cut a 1-1/8 inch entry hole in one 1×8 front panel, centered 6 inches from the top. Add a 1/4 inch drain hole in the floor and a few 3/16 inch ventilation holes near the top of the sides.
  5. Mount the box. Fasten the nest box to the back slats with exterior screws from inside the box so the heads stay out of the cavity. Leave the roof removable for cleaning.

Setting the Entry Hole and Cavity Size

Entry hole size controls which species can use the box. A 1-1/8 inch hole suits chickadees and wrens, and a 1-1/2 inch hole suits bluebirds. Cavity floor space of about 4 x 4 inches works for most small cavity nesters. Confirm the target species before drilling.

Finishing and Placement

Leave cedar unfinished or apply a penetrating exterior oil, not a film finish that can peel. Keep the interior of the nest box bare wood. Position the bench where it gets morning sun and some shade, and avoid spots where predators can climb nearby branches. If you want a wider reference on design choices, the guide Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists covers related dimensions and mounting options.

Tools You Will Need

  • Miter saw or circular saw with a straight guide
  • Drill/driver and a 1-1/8 inch spade or hole saw bit
  • Clamps for holding the frame square while screwing
  • Speed square and tape measure
  • Exterior deck screws and wood glue rated for outdoor use

Common Mistakes to Avoid

  • Skipping the drain hole, which lets water pool and rot the floor.
  • Using interior screws that rust and stain the wood.
  • Mounting the box too high or too low; a height of 5 to 8 feet is typical for many species.
  • Sealing the seat slats edge to edge with no gap, which traps moisture.
  • Choosing an entry hole size without checking the target species first.
  • A hole saw kit for cutting clean entry holes in thin cedar. View on Amazon
  • Exterior-rated deck screws that resist corrosion in outdoor builds. View on Amazon
  • A penetrating exterior cedar oil for finishing the bench without film buildup. View on Amazon

FAQ

Can I use pressure-treated lumber for this bench?

You can, but avoid pressure-treated wood inside the nest box, since chemical treatments can harm birds. Use cedar or untreated pine for the nest box and a treated frame if you prefer.

How high should the birdhouse bench sit off the ground?

Set the bench on level ground with the nest box mounted about 5 to 8 feet high, which is typical for many small cavity nesters. Adjust the height based on the species you want to attract.

How often should I clean the nest box?

Clean it once after each nesting season to remove old nesting material and parasites. Check the box in early spring before nesting begins.

Conclusion

With these birdhouse bench plans free of charge, you can build a functional garden seat and a nest box in one weekend. Match the entry hole to your target species, use exterior fasteners and leave the wood unsealed inside the box. The result is a bench you can sit on and birds that can raise their young in it.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.