Updated November 2026

Free woodworking birdhouse plans give you everything you need to build a sturdy nest box in a single weekend: dimensions, a cut list, and assembly steps. This guide walks you through a simple cedar design with a 1-1/4-inch entrance hole, drainage, and ventilation, so the birds you attract can nest safely and the house lasts for years.

Choose the Right Design and Materials

Before you cut anything, pick a design that matches the species you want to attract. A 1-1/4-inch entrance suits chickadees, titmice, and wrens, while bluebirds need a 1-1/2-inch opening. Use rough-sawn or dressed cedar, pine, or cypress at 3/4-inch thickness. Avoid pressure-treated lumber, painted surfaces, and any wood treated with preservatives that can harm nesting birds.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

Cut and Assemble the Birdhouse

The following cut list builds a house roughly 4 inches square inside, 9 inches tall at the back, and 7 inches tall at the front. Cut all pieces from 3/4-inch stock.

  • Front: 5-1/2 in. × 7 in. (drill the entrance hole 1-1/4 in. diameter, centered 5 in. from the bottom)
  • Back: 5-1/2 in. × 9 in.
  • Sides (2): 4-1/2 in. × 9 in., with the top edge angled to match the roof slope
  • Floor: 4 in. × 4 in.
  • Roof (2): 5-3/4 in. × 6 in., overhanging the front and back

Drill four 1/4-inch drainage holes in the floor and two 1/2-inch ventilation holes near the top of each side. Assemble with exterior wood glue and galvanized 1-1/4-inch deck screws, pre-drilling every fastener to prevent splitting. Leave the roof hinged or attached with a single screw so you can clean the box each fall.

Mount and Maintain the House

Mount the box 5 to 10 feet off the ground on a post or tree, facing away from prevailing winds and afternoon sun. Avoid placing it near feeders, which attract predators and crowd nesting pairs. After each nesting season, open the house and remove old nesting material, which can carry parasites.

  1. Cut all pieces to the cut list and label the front, back, and sides.
  2. Drill the entrance hole and drainage and ventilation holes before assembly.
  3. Glue and screw the sides, floor, front, and back together.
  4. Attach the roof and check that it overhangs the front and back.
  5. Sand the edges lightly and leave the interior unfinished.
  6. Mount the house and clean it after each nesting season.

Tips and Common Mistakes

  • Do not paint or stain the interior; birds need untreated wood.
  • Skip perches on the front, since they help predators more than birds.
  • Drill the entrance hole straight on; a slanted hole can look fine but still lets in larger birds.
  • Check that the floor has drainage holes, or moisture will build up and harm chicks.
  • Measure the entrance hole with a drill bit before you start, not after.

If you are new to these builds, the Free Birdhouse Plans for Laser Cut: 3 Best Patterns and Plans (2026) article covers a different approach, and Wren Birdhouse Plans Free: Build a Cedar House in One Weekend suits small species with a tighter entrance. For a larger, multi-species option, see Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists.

A drill with a sharp set of bits makes the entrance hole clean and accurate, which matters more than any other step. View on Amazon

Exterior wood glue and galvanized deck screws keep the joints tight through rain and freezing weather. View on Amazon

A small sanding block lets you smooth the outside edges without rounding the entrance hole. View on Amazon

FAQ

What wood is best for free woodworking birdhouse plans?

Cedar, pine, and cypress are the most common choices because they resist rot and stay untreated. Avoid pressure-treated lumber and any painted or stained interior surfaces.

How big should the entrance hole be?

A 1-1/4-inch hole suits chickadees, titmice, and wrens, while bluebirds need 1-1/2 inches. Match the hole size to the species you want to attract.

Where should I hang a finished birdhouse?

Mount it 5 to 10 feet off the ground, facing away from strong wind and afternoon sun. Keep it away from bird feeders to reduce predator visits.

Conclusion

With these free woodworking birdhouse plans, you can build a durable nest box from one board and a few screws. Follow the cut list, drill the holes before assembly, and clean the house after each season. A well-built birdhouse can host nesting pairs for many years.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.