Updated November 2026

Frank Lloyd Wright birdhouse plans borrow the horizontal lines, deep overhangs and boxy massing of his Prairie School houses and scale them down to a nest box. You can build one from a single 1×6 cedar board or a few pieces of scrap, and the result works for wrens, chickadees and bluebirds when you size the entry hole correctly. This guide gives you a cut list, the assembly order and the details that keep the box dry and safe for birds.

Plan the Prairie-Style Proportions

Wright’s houses are long, low and strongly horizontal, so the birdhouse version should be wider than it is tall. A practical footprint is 6 inches square with a roof that extends 2 to 3 inches past the walls on the front and sides. The roof should be flat or very low-pitched, not steep, which is the single biggest visual cue that the design comes from the Prairie style.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

Keep the interior dimensions appropriate for your target species. For a small cavity nester such as a house wren, a floor of 4 by 4 inches and an interior height of 6 to 8 inches works well. Set the entry hole at 1 1/8 inches for wrens and chickadees, or 1 1/2 inches if you want to attract bluebirds, and place it about 6 inches above the floor.

Build the Box: Cut List and Assembly

Use 3/4-inch cedar, cypress or untreated pine. Avoid pressure-treated lumber, and do not paint or stain the interior. Cut these pieces from a 1×6 board about 6 feet long:

  1. Two side walls: 6 1/2 in. x 8 in., angled top edges set to match the roof slope
  2. Front and back: 6 1/2 in. x 8 in. each
  3. Floor: 5 in. x 5 in., with 1/4-inch drainage holes drilled in each corner
  4. Roof panels (two): 7 1/2 in. x 8 in. each, for a slight gable or a flat roof with one panel
  5. Front-to-back spacer strips: 1 in. x 1 in. x 5 in., for a ventilation gap under the roof

Assemble with exterior-grade wood glue and 1 1/4-inch galvanized or stainless exterior screws. Pre-drill every screw to prevent splitting, and fasten the floor so it sits 1/4 inch above the bottom edges of the walls to allow drainage. Attach the roof panels with a 1/2-inch overhang on the front and sides. Finish the exterior with a penetrating oil or a light exterior stain, and leave the inside bare.

Mount It Safely

Hang the box 5 to 10 feet off the ground on a post or a sheltered tree trunk, facing away from prevailing winds. Use a predator guard or a smooth metal baffle if cats or raccoons are common in your area.

Tools and Materials Checklist

  • One 1×6 cedar board, about 6 feet long
  • Table saw, miter saw or circular saw with a straight guide
  • Drill with 1 1/8-inch and 1 1/2-inch bits and a 1/4-inch bit for drainage
  • Exterior wood glue and 1 1/4-inch exterior screws
  • Sandpaper, 120 grit, and a penetrating exterior finish

A stable straight edge makes the roof and wall cuts far more accurate, and a clamp keeps the parts square while the glue sets. Use a bit set with a hole saw attachment if you prefer a clean round entry.

  • A metal combination square for marking square cuts and the roof angle. View on Amazon
  • A set of spring clamps to hold the walls while the glue cures. View on Amazon
  • A Forstner bit set for clean entry holes without tear-out. View on Amazon

Common Mistakes to Avoid

  • Making the roof too steep, which loses the Prairie look and sheds the wrong visual weight.
  • Skipping the floor drainage holes, which lets water pool and rot the base.
  • Sizing the entry hole for the wrong species, which either excludes birds or lets in predators.
  • Painting the interior, which can trap moisture and harm nestlings.

Frank Lloyd Wright Birdhouse Plans FAQ

What wood is best for these birdhouse plans?

Cedar is the most common choice because it resists rot and stays stable outdoors. Cypress and untreated pine also work well if they are sealed on the outside only.

What hole size should I use?

Use 1 1/8 inches for wrens and chickadees and 1 1/2 inches for bluebirds. Match the size to the species you want to attract.

Do I need to finish the inside?

No. Leave the interior unfinished so the wood stays natural and no coating can harm the birds.

Conclusion

These Frank Lloyd Wright birdhouse plans give you a clean, horizontal nest box with a low roof and a practical interior. Cut it from cedar, drill the drainage holes and size the entry for your target species. Mount it out of reach of predators, and you have a build that looks good in the yard and works for the birds.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.