Updated November 2026

Tufted titmouse birdhouse plans call for a simple box with a 1-1/4 inch entrance hole, about 4 by 4 inches of interior floor, and 8 to 10 inches of depth from floor to the hole. This guide gives you a cut list, assembly steps, and placement tips so you can build a nest box in an afternoon. Titmice are small, adaptable cavity nesters, so a well-sized box with good ventilation and drainage will usually attract them.

Cut List and Materials

Use rough-sawn or dimensional pine, cedar, or cypress boards that are at least 3/4 inch thick. Avoid pressure-treated lumber and painted or stained wood on the interior. The dimensions below produce a box with roughly 4 by 4 inch floor space, which suits tufted titmice well.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Front panel: 1 piece, 3/4 x 5-1/2 x 9-1/2 inches, with the entrance hole drilled 7 inches above the floor
  • Back panel: 1 piece, 3/4 x 5-1/2 x 14 inches, extended top for mounting
  • Side panels: 2 pieces, 3/4 x 4-1/2 x 9-1/2 inches (angled top optional)
  • Floor: 1 piece, 3/4 x 4 x 4 inches, with 1/4 inch drainage holes at each corner
  • Roof: 1 piece, 3/4 x 6 x 7 inches, hinged or screwed for access

Add 1-1/4 inch exterior screws or galvanized nails, a 1-1/4 inch spade or hole saw, and a supply of wood glue.

Step-by-Step Assembly

  1. Cut all pieces to size and mark the entrance hole center on the front panel, 7 inches above the bottom edge.
  2. Drill the 1-1/4 inch entrance hole with a spade bit or hole saw. Sand the edges smooth so birds do not catch their feet.
  3. Drill four 1/4 inch drainage holes in the floor and two or three 1/4 inch ventilation holes near the top of each side panel.
  4. Attach the floor to the side panels and front with glue and two screws per joint. Keep the floor flush with the bottom edges.
  5. Attach the back panel so it sits flush with the sides. Leave the top of the back extended for mounting.
  6. Fasten the roof with a slight overhang on the front and sides, about 1 inch, to shed rain away from the entrance.
  7. Add a rough surface inside the front wall, such as shallow horizontal grooves, so chicks can climb toward the hole.

Mounting and Placement

Mount the box 5 to 10 feet off the ground on a tree trunk or fence post, facing away from prevailing winds and direct afternoon sun. Titmice prefer wooded edges and yards with mature trees, so a spot near shrubs or brush gives them cover. Avoid placing the box where cats or raccoons can reach it easily.

For a wood-based design that uses similar joinery, see our guide to Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists. If you want to try a different cavity nester first, Plans for a Bluebird Birdhouse: Build One in a Weekend covers a box with a similar footprint.

A quality spade bit in the 1-1/4 inch size makes a clean entrance hole without splintering. Use View on Amazon for the most accurate hole.

Exterior-grade wood glue holds up to rain and temperature swings. View on Amazon is a reliable choice for joints that will see weather.

Stainless or galvanized exterior screws resist rust and keep the box together for years. View on Amazon fits this kind of build well.

Common Mistakes

  • Using a hole larger than 1-1/4 inches, which lets in starlings and house sparrows.
  • Skipping drainage holes, which allows moisture to build up and rot the floor.
  • Painting or staining the interior, which can harm nesting birds.
  • Mounting the box too low or in full sun, which overheats the nest.
  • Cleaning the box during nesting season. Clean it out after the breeding season ends.

FAQ

What hole size do tufted titmice need?

A 1-1/4 inch entrance hole is the standard size for tufted titmice. Larger holes allow competing species to enter and take the nest.

When should I put up a titmouse box?

Install the box in late winter or early spring, before nesting begins. Titmice often start looking for nest sites while it is still cold.

Do tufted titmice need a perch on the birdhouse?

No perch is needed. Titmice cling to the entrance hole and the surrounding wood, and a perch can actually help predators reach the nest.

Conclusion

With a 1-1/4 inch entrance, a 4 by 4 inch floor, proper drainage, and a mounting height of 5 to 10 feet, these tufted titmouse birdhouse plans give you a box suited to the species. Build it from untreated wood, place it in a sheltered spot, and leave it undisturbed during nesting. A simple, well-made box is often all a pair of titmice needs.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.