Updated November 2026

This guide gives you a complete, buildable plan for a simple wood birdhouse using a single 1×6 cedar or pine board. You will get a cut list, a drilling layout for the entrance hole, and an assembly sequence that produces a box suited to common backyard songbirds like chickadees and house wrens. Most builders can finish the project in an afternoon with basic hand tools.

Choose the Right Wood and Dimensions

Untreated cedar, pine or cypress works best. These woods resist rot and do not release the fumes that paint, varnish or pressure-treated lumber can produce. Avoid plywood with exposed glue lines and never use treated lumber, which can contain compounds that harm birds.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

The plan below uses a 1×6 board that measures about 5½ inches wide after milling. Confirm your actual board width before cutting, because a dimensional 1×6 is often narrower than its label.

Cut List

Part Quantity Dimensions
Front and back panels 2 5½ in. wide × 9 in. long
Side panels 2 5½ in. wide × 7 in. long
Floor 1 4 in. × 4 in.
Roof panels 2 5 in. wide × 6 in. long

Cut the front panel to length first, then use it to mark the other pieces so everything matches. Square every end with a miter saw or a fine-tooth hand saw.

Build the Box Step by Step

  1. Cut all parts to the sizes above and sand the faces and edges lightly with 120-grit paper.
  2. Drill the entrance hole in the front panel, 1¼ inches in diameter, centered horizontally and placed 6 inches down from the top edge. A 1¼-inch hole keeps out larger birds and most predators.
  3. Drill four to six ⅛-inch ventilation holes near the top of both side panels and a few small drainage holes in the floor.
  4. Glue and screw the sides to the floor, keeping the floor inset slightly so water runs off.
  5. Attach the front and back panels to the sides. Use two 1¼-inch exterior screws per joint, drilled with a pilot hole to prevent splitting.
  6. Set the roof panels so they overhang the front by about 1 inch and the back by about 2 inches. This overhang shelters the entrance from rain.
  7. Attach the roof with hinges or screws. A hinged roof lets you clean the box at the end of the season.

Mounting Height and Location

Mount the box 5 to 10 feet off the ground, facing away from prevailing winds and away from direct afternoon sun. Avoid placing it near feeders, which attract predators and crowd nesting territories. A related read: 4 Best Hard Wood Flooring Installation Kits and Tools for DIY Renovators.

Common Mistakes

  • Using a hole larger than 1¼ inches, which lets starlings and house sparrows take over the box.
  • Skipping the floor drainage holes, which leaves nesting material soggy after rain.
  • Painting or staining the interior, which can release fumes and tempt birds to peck at residue.
  • Driving screws through the wood without pilot holes, which splits the thin boards.
  • Mounting the box with nails, which makes cleaning and monitoring harder over time.
  • Exterior wood screws hold the joints through seasonal swelling and shrinking better than nails. View on Amazon
  • A Forstner bit set produces clean, flat-bottomed holes for the entrance and ventilation. View on Amazon
  • A combination square helps you check that cuts and assembly stay square. View on Amazon

FAQ

What size entrance hole should a birdhouse have?

A 1¼-inch hole suits chickadees, titmice, and most wrens. Smaller holes, around 1 to 1⅛ inches, fit wrens and bluebirds, while larger holes admit species that may compete with or prey on smaller birds.

Can I use pressure-treated lumber for a birdhouse?

No. Pressure-treated wood contains preservatives that can harm birds, so choose untreated cedar, pine or cypress instead. If you are unsure about a specific material, check with a local wildlife or extension office.

How often should I clean the birdhouse?

Clean the box after each nesting season to remove old nesting material and parasites. Wait until the birds have fledged, and wear gloves and a dust mask while cleaning.

Conclusion

With one 1×6 board, a 1¼-inch entrance hole and careful assembly, you can build a durable nest box in an afternoon. Follow the cut list, place the box at a safe height, and clean it once a year. Using these DIY wood birdhouse plans gives you a reliable home that backyard birds will use season after season.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.