Updated November 2026
Cutting a slot in wood with a router takes one pass per depth increment, a fence or straightedge to keep the cut straight, and a bit that matches the width you need. This guide walks through setup, the cutting sequence and the checks that keep slots square and clean. By the end, you will be able to cut a slot that fits a panel or shelf without rocking or burning.
Choose the Right Bit and Router Setup
A straight bit sized to your slot width is the simplest choice. Use a bit whose diameter equals the slot width, or use a smaller bit and make two passes offset by a few thousandths of an inch. Most woodworkers prefer a plunge router for slots, because you can start the bit inside the workpiece without tipping the base. For a full guide to bit types, see How to Router a Slot in Wood: A Step-by-Step Guide for Beginners.
Shopping for one? See our guide: 5 Best CNC Router Wood Cutting Machines for Hobbyists in 2026.
Before you start, confirm the following: A related read: Best Wood Routers for Woodworking.
- The bit is seated firmly and the collet is tight.
- The router speed matches the bit size. Larger bits need slower speeds.
- Your workpiece is clamped flat to the bench.
Set Depth and Mark the Slot Layout
Mark the slot’s start and end points with a pencil and a square. Extend the lines across the face so you can check alignment mid-cut. Set the depth in passes of no more than about one-quarter of the bit diameter for hardwoods, and about one-half for softwoods. A slot 3/4 inch deep cut in hardwood, for example, takes roughly four passes with a 1/4 inch bit.
Clamp a straightedge or fence to the workpiece, offset from the slot line by the distance between the bit’s edge and the router base’s guide edge. Measure this offset on a test scrap before you cut the real piece.
Cut the Slot in Passes
Plunge and Make the First Pass
Set the router on the fence with the bit retracted, turn it on, and lower the bit slowly into the start point. Move the router along the fence in the direction opposite to bit rotation, so the bit cuts into the wood rather than pushing away from it.
Deepen in Stages
Return to the start, lower the bit by the next depth increment, and repeat. Keep feed rate steady. If the router bogs down or the wood smokes, slow the feed or take a shallower pass.
Finish the Edges
If you used a smaller bit for two offset passes, run the second pass after the first is complete. This removes the ridge and leaves a flat-bottomed slot.
Check Fit and Clean the Slot
Test-fit the panel or part before final passes. A slot that is a few thousandths undersized can be widened with one light pass. Use a sharp bit to reduce tearout, and sand lightly only if needed to keep the edges crisp.
Common Mistakes
- Cutting the full depth in one pass, which causes burning and bit deflection.
- Feeding the router against bit rotation, which can pull the router off line.
- Forgetting to account for the offset between the bit and the fence.
- Using a dull bit, which tears the wood and widens the slot unevenly.
- Skipping a test cut on scrap of the same species and thickness.
Recommended Gear
- Plunge router: Lets you start and stop the bit inside the workpiece, which suits closed slots and stopped cuts. View on Amazon
- Straight router bits: Choose a set that covers the slot widths you use most often, so you can match the bit to the slot without custom sizing. View on Amazon
- Clamp-on straight edge guide: Keeps the router tracking parallel to your marked layout across long slots. View on Amazon
FAQ
Can I cut a slot with a fixed-base router?
Yes, but you must start the bit at the edge of the workpiece or drill a starter hole first. A plunge router is easier for slots that begin and end inside the board.
How deep should each pass be?
For hardwoods, keep each pass to about one-quarter of the bit diameter. Softwoods can handle roughly half the bit diameter per pass.
How do I keep the slot from wandering?
Clamp a straightedge to the workpiece, keep steady pressure against it, and use a sharp bit at a moderate feed rate. Check alignment against your marked lines after each pass.
Conclusion
Cutting a slot in wood with a router comes down to choosing the right bit, setting depth in shallow passes, and guiding the router against a fence. Test on scrap first and check fit before the final pass. With these steps, your slots will come out square, clean and ready for assembly.
Related reading
- Wood Thread Cutting Router Bit: How to Cut Threads in Wood with a Router
- Router Bit for Cutting Circles in Wood: 5 Best Picks Compared (2026)
- Cutting Solid Wood Worktops with a Router: A Step-by-Step Guide
- Cutting Notches in Wood with a Router: A Step-by-Step Guide for Beginners
- 7 Best Router Wood Cutting Machine Options for Hobbyists (2026)
- 7 Best Router Bits for Cutting Wood Options for Every Project (2026)
