Updated November 2026

To use a router to plane wood, you mount the router to a flat sled, set the bit so it cuts just below the surface, and make several shallow passes across the board. The result is a flat, smooth surface on stock too wide or too warped for a hand plane or jointer. This method works well for flattening slabs, leveling glue-ups and dimensioning rough lumber.

What You Need Before You Start

Gather the right tools before you set anything up. A plunge or fixed-base router with a large surface bit gives the best results, and a straight-cutting bit of at least 1/2 inch diameter is the usual choice.

Shopping for one? See our guide: Wood by Wright Router Plane Compared: 7 Best Picks for 2026.

  • A router with a stable base and a collet that holds the bit firmly
  • A surface planing bit (often called a router planer bit) with carbide cutters
  • A flat sled or rails made from MDF or plywood, wider than the router base
  • Shims or stop blocks to keep the sled level on the workpiece
  • Clamps, dust collection, eye and hearing protection

Step-by-Step: Setting Up the Router and Sled

  1. Build or prepare the sled. Make a frame that sits on the high spots of your board and leaves the router base riding on a flat surface. Check the rails with a straightedge.
  2. Secure the workpiece. Clamp the board so it cannot shift. Shim any rocking, especially on slabs.
  3. Install the bit. Insert it fully into the collet, then pull it back about 1/16 inch before tightening. Bottom out the bit against the collet to reduce chatter.
  4. Set the depth. Start with a shallow setting of about 1/32 inch. Surface planing bits are not meant to remove large amounts in one pass.

Making the Passes

Work with the grain and keep the router moving. Stopping in one spot leaves burn marks, and cutting too deep causes tear-out and motor strain.

  1. Start the router before it touches the wood, then lower it onto the sled rails.
  2. Move the router in a steady, overlapping pattern across the full width. Overlap each pass by about one-third of the bit diameter.
  3. Remove a little more material each pass, up to about 1/16 inch per pass for most hardwoods.
  4. Check flatness with a straightedge after each pass. Stop when the surface is uniform and free of high spots.

Reading the Surface as You Go

Fresh cuts show high spots as shiny or unmarked areas. Keep working until the whole surface shows an even, matte cut pattern. If one end cuts faster, check for shims that have shifted or a sled that is not square.

Common Mistakes

  • Cutting too deep in one pass, which causes chatter and rough surfaces.
  • Moving the router against the grain on figured wood, which tears out fibers.
  • Letting the bit sit still while the motor is running, which scorches the wood.
  • Skipping the straightedge check, so the board ends up flat in some areas only.
  • Using a bit that is dull or has loose cutters.
  • Surface planing router bit: Designed for flattening wide boards with a large cutting diameter.
    View on Amazon
  • Straightedge or aluminum ruler: Lets you check flatness quickly between passes.
    View on Amazon
  • Dust collection hose and shop vac adapter: Keeps chips out of your face and off the sled.
    View on Amazon

For more on the tool itself, see Wood River Router Plane: How to Set Up and Use One (2026) and How to Use a Handheld Wood Router: A Step-by-Step Guide for Beginners. If you are working with a fixed table, How to Use a Wood Router Table: A Step-by-Step Guide for Beginners covers those setups. For bit choices, Wood Router Bits Uk: How to Choose the Right Bit for Your Project is a useful reference.

FAQ

Can a router plane a board as well as a jointer?

A router sled can produce a flat surface on wide boards that a jointer cannot handle. Results depend on how carefully you set up the sled and how many light passes you make.

What depth should each pass be?

Most woodworkers take passes of about 1/32 to 1/16 inch. Lighter passes reduce tear-out and strain on the motor.

Do I need a router table for this?

No. A handheld router on a flat sled works for planing. A router table is better suited to edge work and shaping.

Conclusion

A router on a well-built sled can flatten wide or warped stock with a clean, even surface. Take shallow passes, check flatness often and keep the bit sharp. Build your sled carefully, and the results will be worth the setup time.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.