Updated November 2026
Coffee can birdhouse plans give you a fast, low-waste way to build a small nest box for chickadees, wrens, and similar cavity nesters. You will finish with a simple wooden box made from a coffee can-sized cylinder or a scrap-wood box shaped to match, with the correct entrance hole, drainage, and ventilation. The whole build takes a few hours with basic hand tools.
Gather Materials and Plan the Dimensions
Most coffee can birdhouse plans use a 3-pound coffee can as the core, because its diameter sets the interior space. Measure your can first. Its inside diameter should be roughly 6 inches, which suits chickadees and titmice. If your can is noticeably smaller, plan for a wren-sized house instead.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
Use untreated cedar, pine, or fir at least 3/4 inch thick. Avoid pressure-treated lumber and painted or stained wood, since fumes and chemicals can harm nestlings.
- One 3-pound coffee can, cleaned, label removed
- One piece of 3/4-inch untreated board about 6 x 12 inches for the floor, roof, and back panel
- Exterior wood screws or galvanized nails
- A 1 1/8-inch hole saw or spade bit for the entrance
- A drill, a saw, sandpaper, and a tape measure
Cut the Floor, Roof, and Mounting Panel
Cut the floor to match the can’s diameter so it sits flush at the bottom. Drill four 1/4-inch drainage holes in the floor corners. Cut the roof about 2 inches larger than the can on all sides so rain runs off and the overhang shades the entrance.
Cut a back panel about 4 inches wide and 10 inches tall. Attach the can to this panel with two screws through the can’s side near the top and bottom. The panel becomes the mounting surface.
Drill the Entrance and Ventilation Holes
Mark the entrance hole about 6 inches above the floor on the can’s face. For chickadees, drill a 1 1/8-inch hole; for house wrens, use 1 inch. Drill the hole slowly to avoid tearout, and sand the edges smooth so birds don’t scrape their feathers.
Drill two or three 1/4-inch ventilation holes near the top of the can, just under the roof line. Ventilation keeps the nest from overheating in summer.
Assemble and Mount the Birdhouse
- Attach the floor inside the can by driving screws through the can’s base, or simply set the can on the floor piece and screw it into place.
- Attach the roof with two screws, keeping it hinged or removable so you can clean the house after nesting season.
- Mount the house on a pole or fence 5 to 10 feet off the ground, facing away from prevailing winds and direct afternoon sun.
For more build options, see the Simple Birdhouse Plans PDF: A Step-by-Step Build for Beginners and Round Birdhouse Plans Free: A Step-by-Step Build for Beginners. If you want a species-specific size, check Wren Birdhouse Plans Free: Build a Cedar House in One Weekend and Tufted Titmouse Birdhouse Plans: A Step-by-Step Build Guide.
Recommended gear
- Hole saw kit: Makes clean, correctly sized entrance holes in thin board. View on Amazon
- Galvanized exterior screws: Resist rust and hold up outdoors. View on Amazon
- Cordless drill driver: Speeds up drilling and driving screws without tiring your hands. View on Amazon
Common Mistakes
- Using pressure-treated or painted wood, which can release harmful residue.
- Drilling an entrance hole that is too large, letting in predators or competing species like starlings.
- Skipping drainage holes, which lets water pool and rot the floor.
- Mounting the house in full sun, which can overheat the nest.
- Forgetting to clean the box after each nesting season.
FAQ
Can I use a metal coffee can for a birdhouse?
Yes, but the metal can overheat in direct sun and holds moisture. Wrap the outside in untreated wood or paint it a light color, and keep the can well ventilated.
What size entrance hole do I need?
Use a 1 1/8-inch hole for chickadees and titmice, and a 1-inch hole for house wrens. Smaller holes keep out larger birds and predators.
When should I clean out the birdhouse?
Clean it once nesting season ends, usually in late summer or fall. Remove old nesting material and scrub the floor with a mild solution of water and a little vinegar, then let it dry completely.
Conclusion
With a coffee can, a few boards, and a hole saw, you can build a functional nest box in an afternoon. Pay close attention to the entrance size, drainage, and mounting height. Those three details make the biggest difference in whether birds will move in.
