Updated November 2026

Woodworking plans for cutting boards give you a clear path from rough lumber to a finished kitchen board. In this guide you will choose a wood species, lay out a simple edge-grain board, glue up the panel, and finish it with a food-safe oil. The whole build takes a weekend and uses only basic shop tools.

Choose the Right Plan and Wood

Most cutting board plans fall into two types: edge-grain boards, which are faster to make, and end-grain boards, which are gentler on knife edges but take more time. For a first project, an edge-grain board around 12 × 16 inches with a 1-inch thickness is a practical size. Hard maple, black walnut and cherry are common choices. Avoid oily or toxic species such as some exotic rosewoods, and stick with domestic hardwoods you can confirm are food-safe.

Shopping for one? See our guide: Quilt Rack Plans Woodworking: 4 Best Builds for Beginners (2026).

Cut List and Milling Steps

A typical 12 × 16 inch edge-grain board uses strips about 1½ inches wide, cut from 4/4 stock planed to 13/16 inch. Mill your boards flat and square before cutting strips, and keep the grain direction consistent across the glue-up.

  1. Plane or sand stock to a uniform thickness, about 13/16 inch.
  2. Rip strips to 1½ inches wide on the table saw, with the blade set square.
  3. Crosscut strips to a little over 12 inches so you can trim them later.
  4. Arrange strips in a pattern, alternating grain direction for a stable panel.

Glue Up and Shape the Board

Apply a food-safe, water-resistant wood glue to the edges of each strip and clamp the panel evenly, using cauls to keep the surfaces flush. Let the glue cure fully before you remove the clamps. Once the panel is dry, run it through a planer or sand it flat, then trim it square on the table saw. Round the corners and the edges with a router and a roundover bit, or sand them by hand.

Finish for Food Safety

Finish the board with a food-safe mineral oil or a beeswax-and-oil blend. Apply several coats, letting each soak in for at least 20 minutes before wiping off the excess. Reapply every few weeks at the start and as needed afterward. Never run a cutting board in the dishwasher, and dry it on its edge after washing.

Tools and supplies checklist

  • Table saw or miter saw
  • Thickness planer and jointer (or a flat sled for hand planing)
  • Clamps and cauls
  • Router with roundover bit (optional)
  • Food-safe wood glue and mineral oil
  • Sandpaper, 120 to 220 grit

Common Mistakes

  • Skipping the flatten step, which leaves a warped board that rocks on the counter.
  • Using wood glue that is not rated for food contact or outdoor moisture.
  • Over-tightening clamps, which can squeeze out glue and crack thin strips.
  • Choosing a wood with a strong odor or open pores that trap bacteria.
  • Rushing the finish; thin coats soak in better than one heavy coat.
  • Bessey K Body Clamps: Their even clamping pressure helps keep glue-up strips flush. View on Amazon
  • Bosch 1617EVS Router: A reliable router for putting clean roundovers on board edges. View on Amazon
  • Howard Feed-N-Wax: A beeswax and oil blend suited to finishing cutting boards. View on Amazon

If you want more build ideas that use similar joinery and shop skills, see Woodworking Plans for Boxes: A Step-by-Step Build Guide for Beginners and Woodworking Planter Box Plans: A Step-by-Step Build With Cut List.

FAQ

What wood is best for a cutting board?

Hard maple is the most common choice because it is dense, closed-grain and widely available. Walnut and cherry also work well if you want a darker color.

Is an end-grain board better than an edge-grain board?

End-grain boards are gentler on knife edges and look striking, but they take longer to build. Edge-grain boards are faster and still perform well for everyday use.

How often should I oil a cutting board?

Oil a new board every few weeks at first, then as needed when the wood looks dry. Check the surface periodically and reapply oil when it starts to absorb quickly.

Conclusion

With a simple plan, square stock and a food-safe finish, you can build a cutting board that lasts for years. Start with an edge-grain design, measure carefully, and take your time with the glue-up. Consult a professional or your local woodworking shop if you are unsure about food-safe materials or tool safety.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.