Updated November 2026

Wren birdhouse woodworking plans give you a small, sturdy nest box sized for house wrens, Carolina wrens, and similar cavity nesters. This guide walks you through a basic design with a 1-1/8-inch entry hole, a cut list, and assembly steps you can finish in an afternoon. By the end, you will have a box that drains well, opens for cleaning, and stays cool enough for a clutch of eggs.

Wren Birdhouse Plan Dimensions and Cut List

Use 3/4-inch cedar, pine, or another untreated softwood. Thinner stock dries and cracks, and thicker stock makes the box heavier than it needs to be. The finished interior should measure about 4 inches square and 8 to 9 inches tall, which gives wrens room for a nest without leaving space for larger birds to move in.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Two side panels: 4-1/2 in. wide x 9-1/2 in. tall (taper top corners if you want a shed roof look)
  • Front panel: 4-1/2 in. wide x 9-1/2 in. tall, with the entry hole 1-1/4 in. from the top
  • Back panel: 4-1/2 in. wide x 11 in. tall, extended to overhang as a mounting tab
  • Floor: 4 in. x 4 in.
  • Roof: two pieces, each 5-1/2 in. x 6 in., cut at a slight angle for overhang

Drill the entry hole with a 1-1/8-inch Forstner or spade bit, centered horizontally on the front panel. Cut a few 1/4-inch drainage holes in the floor and drill ventilation holes near the top of both side panels.

Assembling the Box

Dry-fit every part before you apply glue or fasteners. Check that the roof overhangs evenly on all sides and that the floor sits flush with the bottom edges of the walls.

  1. Attach the floor to the front and back panels with exterior wood glue and two 1-1/4-inch galvanized or stainless exterior screws per side.
  2. Attach the side panels to the floor and to the front and back. Pre-drill every hole to prevent splitting.
  3. Clamp the assembly square and let the glue cure for at least an hour before adding the roof.
  4. Fasten the roof pieces with hinges or screws. Hinged roofs make annual cleaning much easier.
  5. Add a stainless or galvanized screw through the back tab for mounting, and leave the front unfinished or lightly sanded.

Finishing and Mounting the Nest Box

Leave the interior bare. Paint and stain can release odors, and wrens do best in untreated wood. For the exterior, use a light, non-toxic exterior stain or a single coat of exterior-grade paint in a muted color. Let it cure fully before mounting.

Mount the box 5 to 10 feet off the ground on a post, fence line, or tree. Face the entry away from prevailing winds and avoid direct afternoon sun. Many owners find that a predator guard, such as a metal cone or baffle, reduces losses to raccoons and cats.

Common Mistakes to Avoid

  • Making the entry hole larger than 1-1/8 inches, which lets in starlings and sparrows.
  • Skipping drainage holes, which allows water to pool and chill eggs.
  • Using treated lumber, which can harm nesting birds.
  • Fastening the roof permanently, which makes cleaning out old nests difficult.
  • Mounting the box in full sun, which can overheat the interior on summer afternoons.
  • Forstner bit set: Makes clean, flat-bottomed entry holes without tear-out on thin cedar. View on Amazon
  • Exterior wood glue: Holds joints through seasonal humidity swings better than standard interior glue. View on Amazon
  • Stainless exterior screws: Resist rust and won’t stain the cedar around them. View on Amazon

FAQ

What size hole does a house wren need?

A 1-1/8-inch entry hole is the standard size for house wrens and Carolina wrens. It keeps out larger birds like starlings and bluebirds, which can compete for the box.

Can I use pressure-treated wood for a wren birdhouse?

It is better to avoid it. Chemical preservatives can be harmful to nesting birds, so untreated cedar or pine is the safer choice.

When should I clean out the nest box?

Clean the box after each nesting season, ideally in fall or early winter, to remove old material and parasites. Always check local guidance on nest box maintenance before disturbing any active nests.

Conclusion

With these wren birdhouse woodworking plans, you can build a durable nest box in an afternoon using basic tools. Check the dimensions carefully, leave the interior unfinished, and mount the box where it stays cool and protected. Explore more builds to find a design that suits your yard.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.