Updated November 2026
Woodworking plans for a TV stand give you a clear cut list, a joinery sequence and a finished layout before you touch the saw. This guide walks through a simple open-front stand sized for a typical flat-screen, so you can build it in a weekend with basic shop tools. The final piece should be level, square and strong enough to hold a television and a few media components.
Plan the Dimensions Before You Cut
Measure your television first. Note its width, its depth and the height of the stand you want. Add 2 to 3 inches to the width for breathing room on each side, and allow at least 16 inches of depth so the receiver and cable box have space behind the screen. A stand of about 48 inches wide, 16 inches deep and 20 inches tall works for most 55-inch sets and keeps the screen at a comfortable viewing height.
Shopping for one? See our guide: Quilt Rack Plans Woodworking: 4 Best Builds for Beginners (2026).
Sketch the layout on graph paper or in a drawing program. Mark the shelf positions, the leg or side panel thickness and the location of any cable pass-throughs. A rough sketch saves you from discovering a conflict after the glue has set.
Build the Cut List and Gather Materials
Most stands use 3/4-inch plywood or solid hardwood for the carcass, with 1/4-inch plywood for the back panel. Oak and maple hold screws well, while birch plywood gives a clean, paint-ready face. Use this cut list as a starting point for the 48-inch version:
- Two side panels: 3/4 x 16 x 20 inches
- Top and bottom: 3/4 x 16 x 46 inches
- One middle divider: 3/4 x 15 1/4 x 19 1/4 inches
- Back panel: 1/4 x 46 x 19 1/4 inches
- Two shelves: 3/4 x 15 1/4 x 22 1/2 inches
Cut all parts oversize by about 1/8 inch in length, then trim them to final size with a crosscut sled for square ends.
Cut the Joinery and Assemble the Carcass
Dado the sides to accept the top, bottom and divider. A dado 3/4 inch wide and 3/8 inch deep is strong and easy to cut on a table saw with a dado stack. Test the fit on scrap first, since a snug dado should slide in with light hand pressure and no hammering.
Glue and clamp the carcass square. Check the diagonal measurements; when they match, the box is square. Let the glue cure for at least an hour before you remove the clamps, and longer if the room is cold.
Add the Shelves, Back and Finish
Attach the back panel with glue and brads or small screws so the carcass stays square. Fit the shelves using shelf pins or short dados, depending on whether you want adjustability. Sand all surfaces through 120 then 180 grit, and remove dust before applying finish. A water-based polyurethane or hardwax oil gives durable protection without a strong odor.
Anchor the Stand Safely
A tall, narrow TV stand can tip. Attach a wall anchor or a furniture strap to a stud, especially if children or pets are in the room. Check your local building guidance for anchoring requirements.
Recommended Gear
- Digital calipers help you confirm dado and panel thicknesses before you cut, which keeps joints tight. View on Amazon
- Quick-release bar clamps hold carcass assemblies square while glue cures. View on Amazon
- A stud finder lets you locate framing for safe wall anchoring. View on Amazon
Tips and Common Mistakes
- Cut dados before cutting final panel lengths so the parts stay square.
- Do not skip the diagonal check; a racked carcass will never sit flat.
- Leave a 1/8-inch gap for the back panel to allow for wood movement.
- Test your television’s cable and power routing before final assembly.
- Pre-drill screw holes in hardwood to prevent splitting.
For related builds, see Woodworking Plans for Cribs: A Step-by-Step Build Guide and Woodworking Plans for Bookcases: A Step-by-Step Build With Cut List, which use similar carcass joinery.
FAQ
What wood is best for a TV stand?
Birch or oak plywood is a strong, stable choice for the carcass, while solid hardwood suits a visible top. Choose materials that match your room’s finish and the weight of your television.
How wide should a TV stand be?
Make the stand at least 2 to 3 inches wider than the television’s width. This gives room for speakers and cables without crowding the sides.
Do I need special joinery for a TV stand?
Dadoes with glue are sufficient for most stands and are easy to cut accurately. Add screws through the back or a wall anchor for extra stability.
Conclusion
With these woodworking plans for a TV stand, you can build a level, square unit sized to your television. Measure carefully, cut dados accurately and anchor the finished piece to a stud. Take your time with the glue-up and the result will serve your room for years.
Related reading
- Wren Birdhouse Woodworking Plans: A Step-by-Step Build With Cut List
- Woodworking Toy Plans Free: 5 Builds You Can Make This Weekend
- Woodworking Puzzle Box Plans: A Step-by-Step Guide for Beginners
- Woodworking Plans Chest Drawers: 4 Best Picks for Every Skill Level
- Top 3 Watch Box Woodworking Plans for Beginners and Heirloom Builds
- Top 3 Software for Drawing Woodworking Plans Compared
