Updated November 2026

Good woodworking plans for jewelry boxes give you a cut list, a joinery method and a finishing sequence before you touch a board. This guide walks through a simple, solid-wood box with a sliding or hinged lid, sized to hold rings, earrings and a few necklaces. You will finish with a box that is square, opens smoothly and looks intentional.

Choose a Size and Layout Before You Cut

Start by deciding what the box needs to hold. A typical keepsake box measures about 10 inches wide, 7 inches deep and 4 to 5 inches tall, which fits most jewelry collections without taking up much dresser space. Sketch the interior: a tray with dividers works well for rings and earrings, while a deeper section suits necklaces. If you plan to add a lift-out tray later, leave about 1 inch of clearance at the top of the interior.

Shopping for one? See our guide: Quilt Rack Plans Woodworking: 4 Best Builds for Beginners (2026).

Cut the Parts to Size

Use 3/4-inch stock for the case and 1/4-inch stock for the bottom panel and tray dividers. Mill your boards flat and square first, then cut them to the lengths in your plan. For a 10 x 7 x 4.5-inch box, a typical cut list includes two 10-inch front and back pieces, two 7-inch side pieces, one 1/4-inch bottom panel, and a lid cut from the same stock as the case.

  • Front and back: 2 pieces, 10 x 4-1/2 inches
  • Sides: 2 pieces, 7 x 4-1/2 inches
  • Bottom: 1 piece, 1/4 inch thick, sized to fit a shallow groove
  • Lid: 1 piece, 10 x 7 inches, plus a 1/4-inch-thick breadboard or cap if you want a raised edge

Join the Case and Cut the Grooves

Corner joinery makes or breaks a small box. Rabbet or miter joints are simple and forgiving for beginners, and a spline in a miter adds strength without much extra work. Cut a 1/4-inch groove about 3/8 inch from the bottom edge of all four walls to hold the bottom panel. Dry-fit the case before glue-up and check that the diagonals match. If they differ by more than about 1/16 inch, adjust your clamps until they square up.

Fit the Lid and Hinges

For a hinged lid, mark hinge locations on the back wall and lid so the lid sits flush when closed. Many builders use small brass butt hinges and pre-drill pilot holes to avoid splitting. Test the lid’s swing with a few open-and-close cycles, and sand the edges so the lid does not catch. A sliding lid needs a groove on each side wall instead, and it should slide with light hand pressure.

Sand and Finish

Sand progressively from 120 to 180 to 220 grit. Stop at 220 for most woods, since finer grits can make some finishes less absorbent. Wipe off dust, then apply a finish such as a wiping varnish, shellac or oil-based poly. Lightly sand between coats, and let each coat cure fully. For the interior, many builders use an unfinished or lightly oiled surface so the wood does not affect the metals and fabrics inside.

A combination square helps confirm that corners and panels stay at 90 degrees during assembly. View on Amazon

Bar clamps keep the case tight while glue sets, and you will want at least four for a box this size. View on Amazon

A small block plane is useful for trimming the lid and fitting the sliding panel without sanding away too much stock. View on Amazon

Common mistakes

  • Cutting parts before checking that stock is flat and square, which compounds errors at every joint.
  • Gluing the bottom panel in place, which prevents seasonal wood movement from being accommodated.
  • Making the lid too tight, so it binds against the case when humidity changes.
  • Skipping a dry fit, which hides problems until the glue is already setting.
  • Applying too much finish inside the box, where it can take longer to cure and may leave residue.

FAQ

What wood is best for a jewelry box?

Hardwoods such as cherry, walnut and maple are common choices because they machine cleanly and hold up over time. Avoid woods with strong oils or resins for the interior if you store delicate pieces inside.

Do I need a table saw to build this box?

A table saw makes accurate rips and grooves easier, but you can also use a hand saw, a router and a shooting board. Take your time with layout regardless of the tool you use.

How long does this project take?

Most first-time builders can complete a basic box over a weekend, allowing time for glue to cure and finish coats to dry. Check your finish label for recoat times and cure guidance.

Conclusion

With a clear cut list, careful joinery and a patient finish, a simple box becomes a useful and lasting project. Once you have built one, adjust the dimensions, add dividers or try a different joint to match your skills. Save your plan notes so you can repeat the build with confidence.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.