Updated November 2026
A ripping blade table saw blade is built to cut along the grain, splitting a board lengthwise into narrower strips with a smooth edge. This guide explains how to pick the right ripping blade, set it up square and rip stock safely. By the end, you will know which tooth count and kerf suit your work and how to make consistent rip cuts.
What Makes a Blade Suitable for Ripping
Ripping blades have fewer, larger teeth than crosscut blades. Manufacturers commonly list ripping blades in the 24-tooth range for a 10-inch saw, and this open tooth design clears sawdust quickly when cutting with the grain. Look for a flat-top grind (FTG) or a combination grind with flat-top teeth, since these shear wood fibers cleanly along the length of a board.
Shopping for one? See our guide: 7 Best Dado Blades for Table Saw of 2026: Our Picks Compared.
Blade diameter should match your saw. Check the arbor size and maximum blade diameter in your saw’s manual before buying. Kerf, the width of the cut, also matters: a thin-kerf blade removes less material and asks less of your motor, which helps on underpowered saws.
Setting Up Your Table Saw for Ripping
- Unplug the saw and raise the blade to about 1/4 inch above the top of the stock.
- Check the blade is parallel to the miter slot. Measure front and back of the blade with a rule and adjust until the difference is under about 1/64 inch.
- Set the rip fence to the width you need, measuring from the inside of the blade to the fence face.
- Confirm the riving knife or splitter is aligned with the blade and sits within about 1/4 inch of the teeth at full depth.
- Adjust the blade height so only the top of the tooth clears the workpiece. Exposing too much blade increases kickback risk.
If you are unsure about alignment or your saw’s safety systems, consult the manufacturer’s manual or a qualified tool technician.
Ripping Stock Step by Step
Start with stock that is flat on the bottom and has at least one straight edge. Joint that edge first if needed, then use it against the fence.
- Stand to the side of the blade, not directly behind the workpiece.
- Use a push stick or push block for narrow stock, keeping your hands at least 6 inches from the blade.
- Feed at a steady pace. Let the blade do the cutting rather than forcing the board.
- Support long boards with outfeed rollers or a second person, so the board does not tip as it leaves the saw.
Common Mistakes When Ripping
- Using a crosscut blade for ripping, which leaves rough edges and burns more easily.
- Skipping the blade alignment check after moving or bumping the saw.
- Ripping stock that has not been jointed, causing the fence to pinch the board and cause kickback.
- Removing the riving knife or guard without a clear reason to do so.
- Cutting narrow pieces with the hand instead of a push stick.
For broader setup ideas, see Table for Dewalt Table Saw: A Step-by-Step Guide to Building One (2026) or review 7 Best Table Saws for Woodworking Projects Compared (2026) to match your saw to your projects.
Recommended Gear
- Freud Diablo 24-tooth ripping blade: a widely available ripping-oriented option for general rip cuts in hardwood and softwood. View on Amazon
- Push stick set: keeps hands away from the blade on narrow rips and helps control stock. View on Amazon
- Blade alignment gauge: helps you check that the blade is parallel to the miter slot. View on Amazon
FAQ
How many teeth should a ripping blade have?
Ripping blades typically have fewer teeth, often 24 for a 10-inch saw. Fewer teeth clear sawdust faster when cutting along the grain.
Can I use one blade for both ripping and crosscutting?
Combination blades can handle both tasks reasonably well, but a dedicated ripping blade gives a cleaner edge on long rip cuts. Many shops keep one of each.
Why does my rip cut burn or bind?
Burning often comes from a dull blade, a fence set out of alignment, or feeding too slowly. Check blade sharpness and alignment first.
Conclusion
A ripping blade table saw blade with the right tooth count and flat-top grind will give you clean, efficient rip cuts. Pair it with careful alignment, a straight reference edge and safe feeding habits. Follow the manufacturer’s guidance for your saw and consult a professional if anything feels uncertain.
