Updated November 2026

A table saw jig jointer lets you flatten one face and square one edge of a board using only your table saw. You build a simple sled that rides in the miter slot and holds the workpiece on a flat reference surface, then pass the board over the blade in controlled passes. This guide walks through the design, the build and the setup so you can get reliable results without a dedicated jointer.

How a Table Saw Jointer Jig Works

The jig rides in one miter slot and carries the board across the blade. Because the board is fixed to a flat base, it cannot rock or follow the blade’s arc. The blade is set to take a shallow cut, usually no more than 1/16 inch per pass, and the sled is pushed through so the high spots are removed first. Repeat until the whole face is cut clean.

Shopping for one? See our guide: Harbor Freight Tools Table Saw: 6 Best Picks Compared (2026).

Unlike a standard crosscut sled, a jointer sled is designed for planing a face or edge, so the reference surface and the workpiece clamping are the key details.

Building the Basic Sled

Start with a flat base of 3/4-inch plywood or MDF, roughly 24 inches long and 12 to 16 inches wide. Attach a hardwood runner to the underside that fits your miter slot snugly without binding. Check that the base is square to the runner.

  1. Cut the base to size and square the edges on your saw.
  2. Glue and screw a hardwood runner to the underside, centered and parallel to the long edge.
  3. Add a fence or stop block at the front so the board can be clamped against it.
  4. Mount a toggle or spring clamp on the base to hold the board flat.
  5. Test the sled by sliding it through the slot and confirming it runs straight and does not wobble.

Setting Up the Cut

Raise the blade only slightly above the sled base, so the board projects roughly 1/16 inch above the blade for the first pass. Adjust the height in small increments, checking with a straightedge. Keep the blade square to the table, since a tilted blade will leave a bevel rather than a flat face.

Making the Passes

Clamp the board with its cupped side down on the base. Push the sled through steadily, then return it and make another pass. Continue until the board is flat along its full length. Plane the opposite face the same way after flipping the board, so both faces are parallel.

Checklist Before You Start

  • Sled base flat and square to the runner
  • Runner fits the miter slot without play
  • Blade square to the table and fully guarded
  • Board clamped firmly, with fingers well clear of the blade
  • Riving knife or splitter in place

Common Mistakes

  • Taking cuts that are too deep. Keep each pass shallow to avoid kickback and burning.
  • Using a runner that is loose in the slot, which causes the sled to wander.
  • Skipping a flat reference surface, so the workpiece follows the base’s irregularities.
  • Forgetting to flip the board for the second face.
  • Working with short, thin stock that the clamp cannot hold securely.

If you already own a sled for crosscuts or a dado setup, you can adapt a similar build. For more ideas on table saw work surfaces, see Table for Dewalt Table Saw: A Step-by-Step Guide to Building One (2026) and Circular Saw Table Conversion: A Step-by-Step Guide to Building One.

FAQ

Can a table saw jointer jig replace a benchtop jointer?

For short boards and light flattening, a well-made sled can do the job. Long boards and heavy stock are harder to handle this way, so a dedicated jointer is still more practical for that work.

How deep should each pass be?

Most woodworkers take passes of about 1/16 inch or less. Shallower passes reduce burning and kickback risk.

Do I need a riving knife for this setup?

A riving knife or splitter is recommended for safety. Check your saw’s manual for the correct installation and blade guard arrangement.

Conclusion

A table saw jig jointer is a practical way to flatten and square stock with equipment you may already own. Build a flat, square sled, set shallow passes, and check each board as you go. Work slowly, keep your hands clear of the blade, and consult your saw’s manual for setup guidance.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.