Updated November 2026

Biesemeyer table saw fences are the parallel-guide style rip fences that many table saw owners rely on for accurate, repeatable cuts. This guide explains how the fence is built, how to align it to your blade, and how to check and maintain it so your rip cuts stay straight and safe. Expect a practical walk-through you can follow on a saw with a Biesemeyer-style fence fitted to its rails.

Understand How the Fence Locks and Aligns

A Biesemeyer-style fence clamps to front and rear rails and is positioned by a front-mounted handle and lock. Because the fence rides on the rails rather than a single tube, its accuracy depends on the fence face being parallel to the blade and the rails being clean and flat. Before you adjust anything, confirm the fence locks down evenly at both ends. A fence that binds at one end will drift, even when the scale looks correct.

Shopping for one? See our guide: Harbor Freight Tools Table Saw: 6 Best Picks Compared (2026).

Align the Fence Parallel to the Blade

Parallel alignment is the most important step in any table saw fence setup. Work through it in this order:

  1. Unplug the saw. Raise the blade to full height and mark one tooth with a marker.
  2. Lock the fence about 2 inches from the blade on the front rail and measure to the marked tooth at the front edge of the blade.
  3. Slide the fence back and measure the same tooth at the rear edge of the blade. The two readings should match within a few thousandths of an inch.
  4. If they differ, loosen the fence clamp and adjust the front or rear fence-mounting bolts, or the cam-lock adjustment on your model, until the readings match. Retighten and recheck.

Manufacturers typically specify a parallel tolerance for each model, so check your manual for the exact target before adjusting.

Square the Fence Face and Check the Scale

Once the fence is parallel, confirm the fence face is square to the table. A small error here causes the workpiece to tilt as it passes the blade. Use a square against the table and fence face, and check the reading at the top and bottom of the fence. Then check the scale: set the fence to a common width, such as 3 inches, and measure the actual distance to the blade with a steel rule. Correct the pointer or scale only after the fence itself is square and parallel.

Keep the Fence Accurate Over Time

Fence accuracy drifts with use. Wipe the rails and the table surface with a dry cloth, then apply a light coat of paste wax to the table for smooth movement. Check the lock lever and clamp for wear, and tighten fasteners after the first few weeks of use, since vibration loosens them. Recheck parallelism every few months or after moving the saw.

Common Mistakes

  • Adjusting the scale before the fence is parallel to the blade.
  • Locking the fence without checking that both ends seat evenly on the rails.
  • Leaving sawdust and resin on the rails, which causes binding and false readings.
  • Using the fence as a stop for crosscuts. Use a sled or miter gauge instead.
  • Standing directly in line with the blade when ripping. Stand to the side and use a push stick.
  • Digital caliper: Gives you precise readings when checking front-to-rear parallelism. View on Amazon
  • Machinist square: A reliable square for checking the fence face against the table. View on Amazon
  • Paste wax for table saw tops: Reduces friction so the fence slides smoothly on the table. View on Amazon

FAQ

How often should I check my Biesemeyer table saw fence alignment?

Check parallelism every few months and any time you move the saw or notice rip cuts drifting. A quick measurement at the front and rear of the blade takes only a few minutes.

Why does my fence drift even after I aligned it?

Dust, resin or loose fasteners on the rails are the usual causes. Clean the rails, tighten the mounting hardware and recheck.

Can I use a table saw with a Biesemeyer fence for crosscuts?

No. The fence is designed for rip cuts. Use a miter gauge or crosscut sled for crosscuts, since the fence is not designed to guide the stock across the blade.

Conclusion

A properly aligned fence makes every rip cut more accurate and safer. Set parallelism first, square the fence face second, then check the scale. Keep the rails clean and recheck alignment periodically, and your Biesemeyer-style fence will stay reliable for years.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.