Updated November 2026
A thin rip jig table saw setup lets you cut strips too narrow to safely push past the blade with a standard rip fence. The jig rides in your miter slot, supports the workpiece on its own sled, and keeps your hands well away from the blade. Once you have it built and aligned, you can rip stock to widths of an inch or less with repeatable accuracy.
Why a Thin Rip Jig Beats the Fence for Narrow Cuts
A rip fence works well until the offcut gets narrower than about 3 inches. At that point your hand is squeezed between the fence and the blade, and the workpiece can pinch or kick back. A thin rip jig replaces the fence with a sled-style fixture that carries the stock through the cut. Your fingers stay on the jig, not beside the blade. This approach is widely used in shops for cutting spacers, strips and small parts.
Shopping for one? See our guide: Harbor Freight Tools Table Saw: 6 Best Picks Compared (2026).
Building the Jig: Parts and Layout
Most thin rip jigs use a base that runs in a miter slot, a vertical fence, and a push block or runner system. Plan on a base of plywood or MDF, with hardwood runners sized to fit your slot snugly without binding.
- Cut the base to length and width so it overhangs the table at the front, giving you a stable grip.
- Attach hardwood runners to the underside, sized to slide smoothly in your miter slot.
- Mount a tall fence to the base, square to the blade path, using screws from the bottom side.
- Add a stop block or adjustable stop on the fence for repeat cuts.
- Check that the fence is perpendicular to the base with a reliable square before you use it.
If you want a more permanent setup, a dedicated table saw sled plan is a useful reference. The same sled principles apply, and the Table for Dewalt Table Saw: A Step-by-Step Guide to Building One (2026) article shows how a table can be built to suit a particular saw.
Setting Up and Aligning the Jig
Alignment decides whether your narrow strips come out parallel. Start with the blade. Raise it to full height, then set the jig fence so it runs parallel to the blade within a fraction of a millimeter over its length. Use a dial indicator or a carefully measured tape at both ends of the blade to check. Adjust the fence until the measurements match.
Next, set the blade height so the teeth clear the workpiece by about 1/8 inch. Lower blades reduce kickback risk and produce cleaner edges. Confirm the blade guard and riving knife are installed and working as designed for your saw.
Making the Cut Safely
Feed the workpiece with the jig, not your hands near the blade. Keep the stock tight against the fence and use a push stick or push block for the last few inches. Never stand directly behind the path of the blade. Make one pass, check the result, and then adjust the stop for repeat cuts. Rip multiple pieces by setting the stop once and running each piece through in sequence.
| Step | What to check |
|---|---|
| Before cutting | Blade height, fence alignment, stop position |
| During cutting | Steady feed, hands clear of blade, stock tight to fence |
| After cutting | Measure width, check edge straightness, deburr if needed |
Common Mistakes
- Skipping the alignment check. A slightly off fence makes every strip taper.
- Using a runner that binds in the slot, which causes the jig to wander mid-cut.
- Setting the blade too high. More exposed teeth increase kickback risk.
- Pushing stock through with fingers near the blade instead of using a push block.
- Forgetting to re-check alignment after moving the saw or changing blades.
Recommended Gear
- Dial indicator: Helps you measure blade-to-fence parallelism precisely during setup. View on Amazon
- Push blocks: Keep your hands well away from the blade on the final part of each cut. View on Amazon
- Reliable try square: Useful for checking that the jig fence is square to its base. View on Amazon
FAQ
Can I use a thin rip jig on any table saw?
Most jigs work on any saw with a miter slot that runs parallel to the blade. Check that your slot is clean and the runners fit without binding before you build.
How narrow can a thin rip jig cut?
Results depend on your blade, stock and jig accuracy. Many woodworkers use these jigs for strips well under an inch, but test a sample first and keep your hands clear.
Do I need a riving knife with a thin rip jig?
Yes, keep the riving knife installed and set correctly whenever your saw provides one. It helps reduce kickback during any rip cut, including those made with a jig.
Conclusion
A well-aligned thin rip jig table saw setup gives you clean, repeatable narrow cuts while keeping your hands away from the blade. Take time on alignment and blade height, and always use push blocks on the final stretch. Check your saw manufacturer’s manual for safety guidance specific to your model, and consult a professional if you are unsure about any setup step.
