Updated November 2026
A jointing jig table saw setup lets you straighten and square the edge of a board using the saw you already own. You clamp the stock to a sled or fence-riding jig, run it past the blade, and end up with a flat, straight edge ready for glue-up. This guide walks through the parts, the build, and the test cuts that confirm it works.
Why Use a Jointing Jig on the Table Saw
A jointer is the traditional tool for flattening one edge, but many home shops don’t have room for one. A table saw jig for jointing gets you most of the same result. The jig holds the board against a straight reference so the blade trims a clean edge. It works best on boards up to about 8 inches wide and short enough to control safely on the saw.
Shopping for one? See our guide: Harbor Freight Tools Table Saw: 6 Best Picks Compared (2026).
Materials and Tools You Need
- One piece of flat, stable plywood or MDF for the base, roughly 3/4 inch thick
- A straight hardwood strip for the fence, planed or jointed true
- Two or three toggle clamps or hold-downs
- A combination square and a straightedge for checking
- Glue, screws, and a drill driver
- A cross-cut or push sled if you plan to use the jig with a miter-slot runner
How to Build a Jointing Jig for Your Table Saw
Step 1: Cut the base to size
Cut the base so it sits comfortably on your saw table and extends past the blade on the outfeed side. A base around 24 inches long and 12 inches wide works for most shops, but adjust to your saw. Keep the edges square to each other.
Step 2: Add the runners
Attach hardwood runners to the underside that ride in your miter slots. Fit them snugly with a few thousandths of clearance so the jig slides without rocking. Check that it moves parallel to the blade.
Step 3: Attach the reference fence
Fix the straight strip to the top of the base at a right angle to the blade path. This fence is the surface that will register your board. Check it with a square and adjust before you glue and screw it down.
Setting Up and Making the Cut
Set the blade height so it clears the top of the board by about 1/8 inch. Position the jig so the blade trims only the amount of material you need, usually 1/16 to 1/8 inch per pass. Clamp the board firmly against the fence and feed it steadily past the blade. Keep your hands clear of the blade line and use a push stick at the end of the cut.
| Setup check | What to look for |
|---|---|
| Blade height | Clears the board by about 1/8 inch |
| Fence alignment | Square to the blade, verified with a square |
| Runner fit | Slides smoothly with no side play |
| Hold-downs | Board stays pinned throughout the cut |
Testing and Checking Your Results
Make a test pass on scrap and check the edge with a straightedge held along its length. Light shows through gaps. If the edge is out of square, adjust the fence. Once the test edge is flat, you can confidently joint your project stock. For more on setting up the saw itself, see Table for Dewalt Table Saw: A Step-by-Step Guide to Building One (2026).
Common Mistakes
- Skipping the square check on the fence, which leaves every board slightly out of square.
- Running the jig with loose runners, causing the board to shift mid-cut.
- Taking too deep a pass in a single run, which causes burning and binding.
- Letting your hands drift near the blade instead of using a push stick.
- Not checking the setup again after moving the saw or swapping blades.
Recommended gear
- Toggle clamps hold the board against the fence without tying up both hands, which makes the cut safer. View on Amazon
- A machinist-grade straightedge makes it easy to verify that the jig reference is flat and true. View on Amazon
- Push sticks keep your hands well away from the blade on the final few inches of each pass. View on Amazon
FAQ
Can a jointing jig replace a jointer completely?
For many home projects it can, especially for narrower stock. Wide boards and heavily cupped stock are better handled by a dedicated jointer or a hand plane.
What blade should I use for jointing on a table saw?
A clean-cutting combination blade with a high tooth count gives a smoother edge than a rip blade. Keep the blade sharp, since dull teeth cause burning.
Is a jointing jig safe to use?
It is safer than freehand edge cutting because the board stays controlled against the fence. Always use a push stick, keep your hands clear, and consult your saw’s manual for guard and blade guidance.
Conclusion
A well-built jointing jig turns your table saw into a reliable edge-straightening tool. Check the fence square, keep the runners snug, and make test passes before cutting project stock. With that setup, your glue-ups will start from flat, square edges every time.
