Updated November 2026
Ana White birdhouse plans are a popular starting point for home builders who want a simple, well-documented nest box. This guide shows you how to read a typical plan, prepare your lumber, assemble the box, and avoid the mistakes that make a birdhouse unsafe or unattractive to birds. By the end, you will have a finished house ready to mount.
Understanding the Plan and Cut List
Most birdhouse plans shared by Ana White and similar builders include a cut list, a materials list, and a side-view drawing. Start by checking the board size the plan calls for. Many small birdhouses use a 1×6 or 1×8 board, and the cut list usually gives finished dimensions, so confirm whether your lumber is the actual 3/4-inch thickness or a nominal size.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
Before cutting, mark each piece with its label from the drawing, such as “front,” “back,” “left side,” or “roof.” Mislabeled parts are the most common source of frustration in this kind of build.
Choosing and Preparing Lumber
Use untreated softwood such as cedar, pine, or cypress. Cedar resists rot and holds up well outdoors without paint. Avoid pressure-treated wood, since the chemicals can harm birds and nesting material.
Look for boards without large knots or splits. Plane or sand the interior surfaces smooth enough that the birds have no footholds, but leave the entry area and the inside front wall slightly rough so fledglings can climb out.
Key Measurements to Check
| Feature | Typical Target | Why It Matters |
|---|---|---|
| Floor size | 4 x 4 inches (common for wrens) | Sets the nest footprint |
| Entry hole | 1 1/8 to 1 1/4 inches for chickadees and wrens | Keeps out larger birds and starlings |
| Height above floor | 6 to 8 inches | Protects nest from predators |
| Drainage holes | Four 1/4-inch holes in the floor | Prevents water buildup |
Confirm entry hole sizes against the species you want to attract. Our guide to Wren Birdhouse Plans Free: Build a Cedar House in One Weekend covers the sizing in more detail for small species.
Assembling the Birdhouse Step by Step
- Cut all pieces to the cut list dimensions and dry-fit the box before adding any fasteners.
- Drill the entry hole and drainage holes first, while the pieces are flat and easy to clamp.
- Attach the floor to the two side panels with exterior-rated screws or galvanized nails.
- Add the front and back panels, keeping the edges flush so no gaps let in wind or rain.
- Attach the roof with a hinge or a removable panel so you can clean the box each fall.
- Pre-drill every screw hole near the edge to prevent splitting, then sand any sharp corners.
Use a square at each corner while the glue or screws set. A box that is slightly out of square will still look fine, but the roof will sit crooked and let water in.
Finishing and Mounting the Birdhouse
Leave the interior unfinished. Paint or stain on the inside can release fumes and harm nesting birds. On the exterior, use a water-based, bird-safe stain or leave the cedar natural. Let the finish dry completely before mounting.
Mount the box on a pole or post in a spot that gets morning sun and some shade in the afternoon. Keep it away from feeders, which attract predators and crowd the nest. For a wider set of options after you finish this build, browse Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists.
Recommended gear
A basic set of tools makes this build much more accurate, especially for consistent entry holes and square corners.
- Forstner bit set: Produces clean, flat-bottomed entry holes that are less likely to splinter than standard twist bits. View on Amazon
- Exterior wood screws: Hold up to moisture and temperature swings better than interior screws. View on Amazon
- Combination square: Helps you check that each corner is 90 degrees before you fasten anything. View on Amazon
Common Mistakes
- Using treated lumber or painting the interior, both of which can harm birds.
- Drilling the entry hole too large, which invites starlings and house sparrows.
- Skipping drainage holes, leaving nesting material damp and moldy.
- Mounting the box where cats or raccoons can reach it easily.
- Forgetting to open the box in late fall to clean out old nesting material.
FAQ
Are Ana White birdhouse plans suitable for beginners?
Yes, most of her birdhouse plans use straight cuts and basic fasteners, so they suit someone with a drill and a saw. Dry-fitting the pieces before final assembly will catch most early errors.
What wood is best for a birdhouse built from these plans?
Cedar is the most common choice because it resists rot without chemical treatment. Untreated pine and cypress also work well.
How high should I mount a birdhouse?
Most small songbird houses are mounted about 5 to 10 feet off the ground. Check the requirements for your target species, since some prefer different heights.
Conclusion
Ana White birdhouse plans give you a clear cut list and a dependable build path. Pay close attention to entry hole size, drainage, and unfinished interiors, and your finished house will be safe and inviting for birds. Clean it each fall and it can serve for many nesting seasons.
