Updated November 2026

Birdhouse and feeder combo plans let you build a nest box and a seed feeder as a single unit, so one post gives birds shelter and food in the same spot. Most builds in this style take a weekend with basic hand tools and a few pieces of dimensional lumber. This guide walks through the layout, the cut list logic, and the assembly order so you can finish a combo that works for chickadees, titmice, and nuthatches.

Choose the Right Layout for Your Birds

Start by deciding which species you want to attract, because that choice drives the entrance hole size and the feeder style. A 1-1/8 inch entrance suits chickadees and titmice, while a 1-1/2 inch opening is more typical for bluebirds. If you are unsure, check the Birdhouse and Bird Feeder Plans: 5 Builds You Can Make This Weekend article, which compares several layouts side by side.

Keep the feeder on the opposite side of the post from the house entrance, or mount it on a separate arm. This prevents seed from falling into the nest box and keeps feeding birds from crowding the nest opening.

Build the Cut List and Prepare Materials

Cedar, pine, or cypress are the most common choices because they resist rot without chemical treatment. Use 3/4 inch thick stock for the house walls and floor, and 1/2 inch stock for the feeder tray. Cut all pieces to length before you drill anything, and label each part so you do not mix up the front and back panels.

  1. Rip 3/4 inch cedar into four walls, one floor, and one roof panel for the house.
  2. Cut a 1/2 inch plywood or cedar tray, roughly 8 by 10 inches, with a 3/4 inch lip on all four sides.
  3. Cut a 2 by 2 post or a 1 by 2 mounting arm, long enough to hold the house at 5 to 6 feet off the ground.
  4. Drill the entrance hole, then drill four 1/4 inch drainage holes in the floor and two ventilation holes near the roof line.
  5. Confirm the feeder tray sits level on its mount before you fasten anything permanently.

Assemble the House and Feeder Together

Assemble the nest box first, using exterior-grade screws or galvanized nails. Pre-drill every screw to prevent splitting, especially near the ends of the grain. Leave the roof hinged or attached with removable fasteners so you can clean the box between seasons.

Attach the Feeder Tray

Fasten the feeder tray to the post or arm using two lag screws, positioned so the tray sits at least 6 inches away from the house entrance. Add a small drip edge to the tray so rain runs off rather than pooling in the seed.

Mount the Post

Set the post in a shallow hole or attach it to a pole with pole brackets. Confirm the house faces away from prevailing winds and sunlight to keep the interior cooler.

Common Mistakes

  • Using treated lumber inside the nest box, which can harm nestlings.
  • Placing the feeder directly under the entrance, where droppings and spilled seed accumulate.
  • Skipping drainage holes, which leads to damp nests and mold.
  • Painting or staining the interior of the house.
  • Mounting the combo in full sun, which can overheat the box on warm afternoons.
  • Exterior-grade wood screws: Corrosion-resistant fasteners hold up better than standard steel screws in outdoor weather. View on Amazon
  • Forstner bit set: Clean, flat-bottomed holes make a cleaner entrance hole than a standard twist bit. View on Amazon
  • Pole mounting bracket: A bracket lets you attach the combo to an existing post without digging. View on Amazon

FAQ

What size should the entrance hole be for a combo birdhouse?

A 1-1/8 inch hole suits chickadees and titmice, while 1-1/2 inch works for bluebirds. Choose the size based on which species visit your yard most often.

How high should I mount a birdhouse and feeder combo?

Mount the combo 5 to 6 feet off the ground, which keeps it out of reach of most predators and at a comfortable height for you to clean.

Should I paint or stain the birdhouse?

Paint or stain only the exterior, and leave the interior bare. Interior coatings can give off fumes and make the box uncomfortable for nesting birds.

Conclusion

A well-built birdhouse and feeder combo gives birds a place to nest and a steady food source in one compact project. Follow the cut list, drill the drainage and entrance holes carefully, and place the feeder away from the nest opening. For more plan options, browse Free Birdhouse Feeder Plans: 3 Best Build Guides for Beginners and Birdhouse and Feeder Plans: Build Both in One Weekend (Step-by-Step).

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.