Updated November 2026

Birdhouse plans for woodpeckers call for a different design than most songbird boxes. The entry hole must be the right diameter, the interior needs enough depth for a nest cavity, and the box should be built from thick, untreated wood that holds up to pecking. This guide walks through the measurements, the build order and the placement details so you can finish a box that woodpeckers will actually use.

Choose the Right Dimensions for Your Target Species

Woodpeckers are picky about cavity size, so the first step is matching the box to the species you want. Most common backyard woodpeckers, including downy and red-bellied woodpeckers, use an entry hole of about 1-1/2 inches. Flickers and larger species need a 2-inch or larger opening. Check the species guide you are working from, because the floor size and interior height also change with the bird.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

For a small woodpecker box, a floor of about 4 x 4 inches and an interior height of 9 to 12 inches works well. Cavity-nesting woodpeckers excavate their own space in softwood, so the box should be built to be pecked into. If you are planning a specific build, the Downy Woodpecker Birdhouse Plans: Build a Nest Box in One Afternoon article covers the exact measurements for that species.

Select Wood and Cut Your Parts

Use rough-sawn or solid pine, cedar or cypress at 3/4 inch thick. Avoid plywood with glue lines that can delaminate, and never use pressure-treated lumber or painted stock, since the chemicals and coatings are unsafe for nesting birds. Thicker wood, around 1 inch, gives better insulation and more pecking resistance.

A typical cut list for a small woodpecker box looks like this:

  • Front and back: 1 each, 3/4 x 5-1/2 x 12 inches
  • Sides: 2, 3/4 x 4 x 12 inches (angle the top edges for a sloped roof)
  • Floor: 1, 3/4 x 4 x 4 inches
  • Roof: 1, 3/4 x 6 x 6 inches

Cut the parts square and check that the front and back match, because uneven walls cause drafts and leaks.

Assemble the Box and Drill the Entry Hole

Assemble the box with exterior-grade screws or galvanized nails, leaving the roof unattached so you can clean out the box each season. Drill drainage holes of about 1/4 inch in the floor, and add ventilation holes near the top of each side. Roughen the inside faces of the front and sides with a saw kerf or a rasp so the young birds can climb out.

Mark the entry hole about 6 to 9 inches above the floor, then drill a pilot hole before using a hole saw or spade bit to finish it. Work slowly so the edges stay clean. Use a sanding block to smooth the outside edges, but leave the interior rough.

Quick build checklist

  1. Cut all parts to the cut list and label them.
  2. Drill the floor drainage holes and ventilation holes.
  3. Screw the sides to the floor, then attach the front and back.
  4. Attach the hinged or removable roof.
  5. Drill the entry hole and roughen the interior surfaces.

Mount the Box Where Woodpeckers Will Nest

Mount the box 8 to 20 feet high on a tree trunk or sturdy post, facing away from prevailing winds and direct afternoon sun. Woodpeckers prefer open woodland edges with dead or dying trees nearby. Use a smooth metal mounting strap or a single nail through the back, because screws and rough hardware are hard for birds to avoid while climbing.

Keep the entry hole clear of branches so predators have a harder time reaching it. Clean the box after each nesting season, and remove old nesting material to reduce parasites.

Common Mistakes to Avoid

  • Using an entry hole that is too large, which lets starlings and house sparrows take over.
  • Skipping the drainage holes, which leaves nestlings in wet conditions.
  • Painting or staining the interior, since fumes and residue are harmful to birds.
  • Mounting the box in full sun, which can overheat eggs and chicks.
  • Leaving the interior too smooth, so the young cannot climb to the entry hole.

A hole saw in the correct diameter makes a clean, accurate entry hole, which is the most important measurement in the box. View on Amazon

A stainless or galvanized exterior screw set resists rust and keeps the box together through several seasons outdoors. View on Amazon

A cordless drill with a sharp bit set speeds up the drilling of ventilation and drainage holes. View on Amazon

FAQ

What size entry hole do woodpeckers need?

Most small woodpeckers use an entry hole of about 1-1/2 inches, while flickers and larger species need about 2 inches. Confirm the size for your target species before you drill.

Should I paint a woodpecker birdhouse?

Painting the outside with a light, non-toxic exterior finish is fine, but never paint or stain the interior. Leave the inside bare so the birds have a safe nesting surface.

When should I clean out the box?

Clean the box once nesting season ends, usually in late summer or early fall. Remove old nesting material and check for damage before the next spring.

Conclusion

Using birdhouse plans for woodpeckers that match the species’ entry hole, floor size and wood thickness gives you a box birds will accept. Mount it high, keep the interior bare and clean it every year. With those details right, your box can host woodpeckers for many seasons.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.