Updated November 2026

To build your own birdhouse plans, you need a simple box with the right interior dimensions, an entrance hole sized for your target species, and drainage and ventilation that keep the nest dry. This guide walks you through choosing a design, cutting the pieces, and assembling a sturdy house that a wren, chickadee, or bluebird will actually use. The whole project fits comfortably into one afternoon.

Choose Your Target Bird First

Dimensions depend entirely on the species you want to attract. A house sized for a house wren will be too small for a bluebird, and a bluebird house with a large entrance may invite starlings, which often take over smaller boxes. Start with the bird, then pick the plan. For example, many chickadee boxes use a floor of about 4 x 4 inches, a 1-1/8 inch entrance hole, and an interior height near 8 inches. Bluebird boxes typically use a 5 x 5 inch floor, a 1-1/2 inch entrance, and about 8 to 10 inches of interior height. Check a species-specific reference before you cut anything. The Wren Birdhouse Plans Free: Build a Cedar House in One Weekend plan is a good starting point for small cavity nesters.

Shopping for one? See our guide: Free Birdhouse Feeder Plans: 3 Best Build Guides for Beginners.

Gather Materials and Tools

Use untreated cedar, pine, or cypress, roughly 3/4 inch thick. Pressure-treated lumber and painted or oily surfaces can harm nesting birds. Outdoor-rated exterior screws or galvanized nails work well, and a waterproof wood glue helps the joints hold through seasons of rain.

  1. One 1 x 6 board, about 4 feet long, for all parts (cut to the lengths in your plan)
  2. Exterior screws or galvanized nails, 1-1/4 to 1-5/8 inch
  3. Handsaw or miter saw, drill with a bit set for pilot holes, and a hole saw or spade bit for the entrance
  4. Tape measure, square, and a pencil
  5. Sandpaper, 120-grit, for rough edges and the interior

Cut the Pieces and Drill the Entrance

Cut the front, back, two sides, floor, and roof to the dimensions in your plan. Mark the entrance hole on the front panel, measuring from the top of the board so the hole sits about 6 to 8 inches above the floor for most cavity nesters. Drill the hole square and centered. Roughen the inside of the front panel below the entrance, or add short horizontal grooves, so fledglings can climb out. Drill four to six 1/4 inch drainage holes in the floor and two small ventilation holes near the top of the side panels.

Assemble the Box Step by Step

Assembly goes faster with a consistent order. Work from the floor up.

  1. Attach the floor to the two side panels, keeping the edges flush.
  2. Add the front and back panels. Check for square with a tape measure across the diagonals.
  3. Fasten the roof with a slight overhang on the front, usually 1 to 2 inches, to shed rain away from the entrance.
  4. Leave the roof hinged or removable so you can clean the box each fall.
  5. Sand the exterior edges lightly. Do not paint or stain the inside.

Mount the house on a pole or fence with a predator guard where needed. Position the entrance away from prevailing winds, and aim it east or southeast if you can.

Common Mistakes to Avoid

  • Using an entrance hole that is too large, which lets in starlings and sparrows.
  • Skipping drainage holes, which lets moisture pool and chill eggs.
  • Painting or treating the interior with anything toxic.
  • Mounting the box where cats or raccoons can reach the entrance.
  • Forgetting to clean the box after each nesting season.
  • Exterior screws: Corrosion-resistant screws hold up better outdoors than standard drywall screws. View on Amazon
  • Hole saw kit: A set of hole saws makes clean, round entrance holes in thin boards. View on Amazon
  • Predator guard: A metal baffle keeps climbing animals away from the nest. View on Amazon

FAQ

What wood is best for a birdhouse?

Untreated cedar is the most popular choice because it resists rot without chemicals. Pine and cypress also work well if left unfinished.

How big should the entrance hole be?

It depends on the species. Chickadees use about 1-1/8 inches, while bluebirds use about 1-1/2 inches. Smaller holes keep out larger competitors.

When should I build or hang a birdhouse?

Build and mount the house before nesting season, ideally late winter or early spring. Birds often inspect boxes well before they settle in.

Conclusion

Once you know your target bird, the rest of the build follows a simple pattern: correct dimensions, a properly sized entrance, and good drainage. Start with one reliable plan, build it carefully, and adjust the next box based on what you learn. A well-made house can serve birds for many seasons.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.