Updated November 2026

To build a wren birdhouse plans project that wrens will actually use, you need one 1×6 cedar board, a few screws, and a sized entry hole of about 1-1/8 inches. This guide gives you a complete cut list, assembly order, and the details that matter most for house wrens and similar small cavity nesters. A careful builder can finish the box in an afternoon with basic hand tools.

Gather Materials and Cut the Parts

Use rough or smooth cedar, pine, or other untreated softwood at least 3/4 inch thick. Cedar resists weather and does not need paint. Your cut list for a standard wren box is:

Shopping for one? See our guide: Free Birdhouse Feeder Plans: 3 Best Build Guides for Beginners.

  • Front: 1 piece, 4 inches wide by 8 inches long, with the entry hole drilled 6 inches above the floor
  • Back: 1 piece, 4-1/2 inches wide by 9-1/2 inches long
  • Sides: 2 pieces, 4 inches wide by 9 inches long, with the front and back angled at the top to create a sloped roof
  • Floor: 1 piece, 4 by 4 inches
  • Roof: 1 piece, 5 by 6 inches, sloped to shed water

Cut all pieces square and check them against each other before drilling. Small errors compound quickly in a box this size.

Drill the Entry Hole and Drainage

Mark the entry hole on the front panel, centered horizontally and 6 inches up from the bottom edge. Drill it with a 1-1/8 inch spade or Forstner bit. Wrens are small, but a larger hole lets in starlings and sparrows, which often take over boxes meant for wrens. Drill four 1/4-inch drainage holes in the floor and two small ventilation holes near the top of the sides.

Assemble the Box in the Right Order

Assembly goes faster if you follow a fixed sequence:

  1. Attach the floor between the two side panels, keeping the bottom edges flush.
  2. Fasten the back panel to the sides and floor with exterior screws, pre-drilling each hole to prevent splitting.
  3. Attach the front panel, making sure the entry hole sits centered.
  4. Screw the roof on so it overhangs the front by about 1 inch to shed rain away from the entry.
  5. Scrape the inside walls rough, or score them with a saw kerf, so wrens can climb out easily.

Avoid glue on the inside surfaces. Exterior-rated screws hold better in cedar and make future cleaning simpler.

Mount the Birdhouse Safely

Place the box on a post or fence line 5 to 10 feet off the ground, facing away from prevailing winds and direct afternoon sun. Wrens like some cover nearby, such as shrubs or a brushy edge, but not so much that predators can hide close to the entry. Use a single nail or screw through the back if you attach it to a tree, so you can remove it later for cleaning.

Common Mistakes to Avoid

  • Drilling an entry hole larger than 1-1/4 inches, which invites competing species.
  • Skipping drainage holes, leaving nesting material wet and moldy.
  • Using painted or pressure-treated wood, which can harm birds.
  • Mounting the box in full sun, where nestlings can overheat.
  • Gluing the interior, which leaves no rough surface for chicks to climb.

A sharp spade or Forstner bit in the correct size gives a clean entry hole without tearing the wood. Look for a 1-1/8 inch spade bit set. View on Amazon

A pair of exterior-rated stainless steel screws resists rust and holds well in cedar. View on Amazon

For more size options, see Plans for Wren Birdhouse: A Step-by-Step Guide With Cut List and Wren Birdhouse Plans Free: Build a Cedar House in One Weekend. If you are building for a different species, House Wren Birdhouse Plans: A Step-by-Step Build With Cut List and Carolina Wren Birdhouse Plans: A Step-by-Step Build Guide cover close variations.

FAQ

What size should the entry hole be for a wren birdhouse?

A 1-1/8 inch entry hole suits house wrens and keeps out most larger competitors. Holes wider than about 1-1/4 inches often let in sparrows and starlings.

What wood is best for a wren birdhouse?

Untreated cedar or pine at least 3/4 inch thick works well. Avoid painted, stained, or pressure-treated lumber, since chemicals can harm nesting birds.

When should I mount a wren birdhouse?

Mount it in early spring, before wrens begin scouting territory. Position it 5 to 10 feet high in partial shade for the best chance of occupancy.

Conclusion

A well-made wren box takes one afternoon and a single board of cedar. Follow the cut list, keep the entry hole small, and mount the house in partial shade. With those details right, you give wrens a dependable place to raise their young.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.