Updated November 2026
Chess board woodworking plans give you a clear path to building a flat, good-looking board from a few sheets of stock or solid hardwood. This guide walks through the layout, the cut list, glue-up and finishing, so you finish with a 16-inch board of 64 alternating squares, each 2 inches across. The method works for solid wood or a plywood core with edging.
Plan the Board Size and Wood Choice
A standard board uses 64 squares. At 2 inches per square, the playing surface measures 16 by 16 inches. Add a border of about 1 1/2 inches on each side for a finished outside dimension near 19 by 19 inches, and plan for a 1/2-inch-thick board so it sits flat on a table.
Shopping for one? See our guide: Quilt Rack Plans Woodworking: 4 Best Builds for Beginners (2026).
Choose two contrasting woods. Maple or birch makes a light square, and walnut or cherry makes a dark one. Keep the grain direction consistent across all pieces so the board moves evenly with humidity. If you want a simpler build, use one species and a dark stain or finish on alternating squares.
Cut the Strips and Build the Grid
Rip stock to 2 inches wide and about 16 inches long. You need eight light strips and eight dark strips. Set your table saw fence carefully, make test cuts on scrap, and check that every strip is the same width to within a few thousandths of an inch.
- Glue four light and four dark strips together, alternating colors, to form a 16-inch block.
- Clamp the block and let the glue cure for at least an hour.
- Crosscut the block into eight 2-inch slices.
- Stack the slices with each row offset by one square to create the checkerboard pattern.
- Glue the eight rows together, clamping across the grid to keep it square.
If you are new to glue-ups, our guide on Woodworking Plans for Tables: A Step-by-Step Guide to Building Your First One covers clamp pressure and flat-panel techniques that apply here.
Add the Border and Flatten the Surface
Mill a border from 1 1/2-inch stock, miter the corners, and glue it around the grid. Let it dry fully before sanding. A flush-trim router bit with a bearing guide cleans up any overhang once the glue has set.
Flatten the top with a hand plane or a belt sander. Work diagonally across the grain and check with a straightedge. Sand progressively from 120 to 220 grit, and keep the surface flat rather than chasing perfect edges.
Joinery Options for the Border
Miter joints look clean but need careful clamping. Spline joints are stronger and forgiving of small gaps. Both suit a board that will be handled often.
Finish and Protect the Board
Apply a food-safe oil such as mineral oil or a wiping varnish. Use three thin coats, sanding lightly between coats with 320 grit. Let each coat cure fully before adding the next. Avoid heavy film finishes on the playing surface, since pieces will scratch them over time.
Recommended gear
- A flush-trim router bit with a bearing guide, because it trims the border flush without burning the edge. View on Amazon
- Bar clamps in a range of lengths, since the glue-up needs even pressure across the full 16-inch grid. View on Amazon
- A block plane for final trimming of miters and edges. View on Amazon
Tips and Common Mistakes
- Skipping test cuts on the table saw, which leads to uneven squares.
- Rushing the glue-up without checking for square, so the grid drifts.
- Using wood that has not acclimated to your shop, which can cause cupping.
- Applying thick finish, which can hide the grain and chip easily.
- Sanding too coarse too early, leaving scratches that show after finishing.
For another small project that uses similar glue-up and edge work, see Woodworking Plans Coffee Table: 6 Steps to a Sturdy Build.
FAQ
What size should a standard chess board be?
A common size is 16 inches square with 2-inch squares, giving 64 squares. Some builders use a slightly larger border for a finished look.
Can I build a chess board from plywood?
Yes. Use good-quality hardwood plywood with a solid-wood edge banding, which hides the layers and holds up better to handling.
Do I need a table saw to build this board?
A table saw makes accurate strips easiest, but you can rip them with a circular saw and a straightedge guide if you cut carefully.
Conclusion
With accurate strips, a square glue-up and a flat surface, these chess board woodworking plans produce a board you can use for years. Take your time on the grid, since everything else depends on it. Once you finish one, you can adjust the wood choices and border to suit your style.
Related reading
- Wren Birdhouse Woodworking Plans: A Step-by-Step Build With Cut List
- Woodworking Toy Plans Free: 5 Builds You Can Make This Weekend
- Woodworking Puzzle Box Plans: A Step-by-Step Guide for Beginners
- Woodworking Plans Chest Drawers: 4 Best Picks for Every Skill Level
- Top 3 Watch Box Woodworking Plans for Beginners and Heirloom Builds
