Updated November 2026

Free finch birdhouse plans give you everything you need to build a simple nest box that finches will actually use. This guide covers a basic box design with a cut list, the correct entrance and floor dimensions, and the assembly steps. You can finish the project in an afternoon with basic tools.

Know Which Finch You Are Building For

Most finches that nest in boxes in North America are house finches, and they are the species these dimensions target. American goldfinches usually prefer open shrubs and rarely use enclosed boxes, so a finch-specific box is typically aimed at house finches. Because they are small and nest in cavities and sheltered spots, the box should be compact with a small entrance hole.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

Materials and Cut List

Use untreated softwood such as cedar, pine, or fir, at least 3/4 inch thick. Avoid pressure-treated lumber and painted or stained surfaces inside the box. Cut the following pieces:

  • Front: 1 piece, 6 inches wide × 8 inches tall
  • Back: 1 piece, 6 inches wide × 9 inches tall (extends above the roof for mounting)
  • Sides: 2 pieces, 4 1/2 inches wide × 8 inches tall, with the top edge angled to match the roof slope
  • Floor: 1 piece, 4 inches × 4 inches
  • Roof: 1 piece, 7 inches × 6 1/2 inches, overhanging the front by about 1 inch

Step-by-Step Build

  1. Cut all pieces to size and check that the sides match the front and back heights.
  2. Drill drainage holes of about 1/4 inch in the floor, and roughen the inside of the front panel so young birds can climb out.
  3. Drill the entrance hole in the front panel, centered about 6 inches above the floor. Use a 1 1/8-inch bit for house finches, which keeps out larger birds.
  4. Attach the floor between the sides with exterior wood glue and 1 1/4-inch galvanized nails or screws, leaving the floor set back slightly from the front.
  5. Attach the front and back panels to the sides, keeping the edges flush.
  6. Fix the roof with hinges or screws so you can open it for cleaning in the fall.
  7. Apply no paint or stain on the inside. You can seal the outside with a clear, non-toxic exterior finish if desired.

Mounting and Placement

Mount the box 5 to 10 feet off the ground on a post, fence, or tree, with the entrance facing away from prevailing winds. Keep it in partial shade and away from heavy feeders, since crowding can make birds abandon a site. Do not add a perch, because it gives predators an easy foothold.

A drill with a set of sharp bits makes the entrance hole clean and accurate. A 1 1/8-inch spade or Forstner bit is the size most often used for this box.

View on Amazon

Exterior wood glue and galvanized nails hold the box together through seasons of rain.

View on Amazon

A small hand saw or a miter saw helps keep the angled side cuts accurate.

View on Amazon

Common Mistakes

  • Using pressure-treated or painted wood, which can harm nesting birds.
  • Making the entrance hole too large, which lets in starlings and sparrows.
  • Skipping drainage holes, which lets moisture build up inside.
  • Mounting the box in full sun, which can overheat eggs and chicks.
  • Cleaning the box during nesting season, which can disturb active birds.

FAQ

When should I put up a finch birdhouse?

Install the box in late winter or early spring, before nesting begins. House finches often nest early and may raise several broods in a season.

Should I clean out the box between nestings?

Yes. Remove old nesting material after the season ends, once the birds have finished. Wear gloves and a mask when cleaning.

Will finches use the box if it is painted?

Birds are unlikely to use a painted or stained box on the inside, and the coating can be harmful. Keep the interior bare and only treat the exterior if needed.

Conclusion

With these free finch birdhouse plans, you can build a sturdy nest box from common untreated lumber in a single afternoon. Pay close attention to the entrance hole size and the placement away from direct sun. Check out other designs on our site, like Free Birdhouse Plans PDF: 6 Printable Designs With Cut Lists, if you want to build for more species.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.