Updated November 2026
Free outhouse birdhouse plans give you a small, classic nest box shaped like a tiny backyard privy, and you can build one from a single 1×6 board and a few scraps. This guide walks through a finished cut list, the assembly order, and the details that keep birds safe and the box easy to clean. Expect a build that takes an afternoon with basic tools.
Cut List and Materials
Use cedar, cypress or untreated pine. Avoid pressure-treated lumber, since the chemicals can harm nesting birds. The dimensions below produce a house about 6 inches wide, 6 inches deep and roughly 12 inches tall at the peak, with a front entry for small cavity nesters.
Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.
- (2) side panels: 3/4 in. x 5-1/2 in. x 9 in., with the top edges cut at a 30-degree angle
- (1) back panel: 3/4 in. x 5-1/2 in. x 12 in.
- (1) front panel: 3/4 in. x 5-1/2 in. x 9 in., cut with a 1-1/8 in. entry hole placed 6 in. from the floor
- (1) floor: 3/4 in. x 5 in. x 5 in.
- (2) roof panels: 3/4 in. x 4 in. x 8 in., angled to meet at the peak
- (1) “seat” or “wall” trim piece (optional): 1/4 in. x 6 in. x 1 in., for the classic outhouse look
- Exterior-grade wood glue, 1-1/4 in. exterior screws or galvanized nails, and a pair of hinges or a single screw-on lid
Step-by-Step Assembly
Cut all parts before you start. Dry-fit the pieces so you can check the angles before you commit to glue.
Step 1: Cut the Front Entry Hole
Mark a 1-1/8 in. circle centered 6 in. above the floor line on the front panel. Drill a pilot hole, then finish with a spade bit or hole saw. Sand the edges so they do not chafe young birds.
Step 2: Join the Sides and Back
Glue and screw the side panels to the back panel, keeping all top edges flush. Pre-drill every hole to prevent splitting the cedar.
Step 3: Attach the Floor and Front
Set the floor 1/2 in. in from the bottom edge, which creates a drainage gap at the base. Attach the front panel last so you can reach inside to drive screws. Leave the floor-to-wall gaps open at the seams; this allows ventilation.
Step 4: Build the Roof
Glue and screw the two roof panels so they meet at the peak with a small overhang of about 1 in. on each side. Attach the roof with hinges on the back edge so you can open it for annual cleaning.
Finishing and Mounting
Leave the interior bare and unpainted. Paint or stain only the exterior, and use a water-based, non-toxic finish. Mount the box 5 to 10 feet off the ground on a post or wall, facing away from prevailing wind and direct afternoon sun. Check the Free Bluebird Birdhouse Plans: 5 Steps to Build a Nest Box This Weekend guide if you want species-specific entry hole and mounting heights.
Tools You Will Need
- Miter saw or hand saw for square, accurate cuts
- Drill with a 1/8 in. bit for pilot holes and a spade or hole saw for the entry
- Clamps to hold panels while glue sets
- Sanding block, 120-grit paper
- Combination square and pencil
Common Mistakes
- Using painted or pressure-treated wood, which can release fumes or toxins
- Making the entry hole too large, which lets predators such as starlings and raccoons in
- Skipping the floor gap and trapping moisture that breeds mold
- Sealing every seam, which blocks ventilation and overheats the nest in summer
- Forgetting to plan for cleaning, so the house goes unmaintained after nesting season
Recommended Gear
- Exterior wood glue: a waterproof, D3-rated glue keeps joints tight when the box is exposed to rain. View on Amazon
- Hole saw kit for wood: makes clean, round entry holes without splitting the board. View on Amazon
- Galvanized exterior screws: resist rust and hold up outdoors better than bright steel screws. View on Amazon
FAQ
What wood is best for free outhouse birdhouse plans?
Cedar is the most common choice because it resists rot and stays naturally weather-proof. Untreated pine is a workable alternative if you seal the exterior.
What size entry hole should the house have?
A 1-1/8 in. hole suits wrens and chickadees, while bluebirds usually need about 1-1/2 in. Adjust the hole to match the species you want to attract.
When should I clean out the birdhouse?
Clean the box after each nesting season, ideally in late summer or early fall once the birds have left. Remove old nesting material to reduce parasites before the next spring.
Conclusion
With a single board and a weekend, you can build a charming outhouse-style nest box that birds will actually use. Follow the cut list, keep the interior unfinished, and size the entry hole for your target species. A little planning now means a productive nesting site for years.
