Updated November 2026

To cut a circle in wood with a router, you attach the router to a pivot point with a trammel or circle-cutting jig, set the cutting depth in shallow passes, and rotate the router around a fixed center. The result is a clean, accurate round cutout or disc, whether you are making a tabletop, a clock face or a birdhouse entry hole. The method takes some setup, but it is repeatable once you understand the geometry.

Set Up Your Pivot and Radius

Everything starts with a fixed center point and a known radius. Measure the radius you want from the center of the pivot pin to the outer edge of the bit, not to the outside of the router base. Mark the center on a scrap piece first and test the setup before cutting your project stock.

Shopping for one? See our guide: 7 Best Router Bit to Cut Wood Options for Every Project (2026).

A simple trammel uses a strip of plywood or hardwood with a pivot hole at one end and a second hole at the radius distance. Drive a small brad or dowel through the pivot hole into a sacrificial base board. The router’s base attaches to the trammel through the second hole, so the bit rotates around the pivot as you turn the router.

Choose the Right Bit and Set Depth

A straight bit or a spiral upcut bit works well for most circle cuts. Use a bit diameter that suits your depth and material, and keep the flutes sharp so the cut stays clean. Avoid forcing the router through thick stock in one pass.

Set the cutting depth in passes of no more than about 1/8 inch for hardwoods and about 1/4 inch for softer stock. Make the first pass at the shallow setting around the full circle, then raise the bit in steps until you reach the final depth. Shallow passes reduce tear-out and protect the router motor from strain.

Make the Cut Safely

Clamp the workpiece firmly to the bench so it cannot shift. Keep the trammel secure on the pivot and confirm the router base is fully seated on the stock before turning it on.

  1. Clamp the workpiece and sacrificial base board to the bench.
  2. Drive the pivot pin at the circle center and check that it does not wobble.
  3. Attach the router to the trammel at the set radius.
  4. Set the bit depth for the first pass, about 1/8 inch for hardwood.
  5. Start the router, let it reach full speed, then plunge slowly into the stock.
  6. Rotate the router clockwise around the pivot in one steady motion, letting the bit do the work.
  7. Raise the bit depth and repeat until you reach the final depth.
  8. Stop, unplug, and free the cutout only after the bit has stopped turning.

Work in the correct rotation direction for your router. Feed against the rotation of the bit so the router is pulled into the cut and does not climb away from you.

Finish the Edges

Once the circle is cut, the edge may show slight marks from the bit or chatter from the pass depths. Sand the edge lightly with a sanding block or a random orbit sander, starting around 120 grit and moving to 180 grit. For a smooth, uniform edge on a larger piece, a flush-trim bit with a bearing can clean up the cut against a template.

Common Mistakes

  • Setting the radius from the outside of the router base instead of from the bit’s cutting edge.
  • Taking the full depth in one pass, which causes burning and tear-out.
  • Letting the pivot pin loosen during the cut, which produces an oval instead of a circle.
  • Feeding too fast, leaving rough or uneven walls.
  • Cutting without a sacrificial board, which can blow out the underside of the stock.
  • Trammel or circle-cutting jig keeps the radius fixed so every pass stays on the same circle. View on Amazon
  • Spiral upcut router bit clears chips efficiently and leaves a clean wall in most hardwoods. View on Amazon
  • Sanding block keeps the cut edge flat while you smooth it. View on Amazon

FAQ

Can I cut a circle in wood with a router without a jig?

You can, but accuracy suffers. A jig or trammel holds the radius fixed, which is what makes the circle round and repeatable.

What depth should each pass be?

About 1/8 inch for hardwood and up to 1/4 inch for softer wood is a reasonable starting point. Shallower passes give cleaner results and less strain on the router.

Why does my circle come out oval?

The most common cause is a pivot pin or trammel that shifts during the cut. Check that the pivot is secure and the radius hole is tight before you start.

Conclusion

Cutting a circle with a router comes down to a fixed pivot, an accurate radius and shallow passes. Practice on scrap first to confirm your setup, then cut your project stock with confidence. With a little care, you can produce clean, repeatable circles for furniture, signs and birdhouse parts.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.