Updated November 2026
Learning how to cut curves in wood with a router comes down to one idea: guide the router’s base along a template or a fence while the bit removes material at a controlled depth. Once you set up the template, pick the right bit and feed in the correct direction, you can produce smooth arcs, circles and irregular shapes that match a pattern to within a few hundredths of an inch. This guide walks through the method, the setup and the mistakes that most often ruin a curve.
Choose the Right Method for Your Curve
Most curved router work uses one of two approaches. A template with a pattern bit is the most accurate option for repeat parts, because a bit with a bearing at the tip rides along the template edge and copies its shape exactly. A trammel or circle-cutting jig is better for true circles and arcs of a fixed radius, since it pivots the router around a center point. For one-off freehand shapes, you can use a bit with a bearing and a plywood guide, but accuracy depends heavily on your hand control.
Shopping for one? See our guide: 7 Best Router Bit to Cut Wood Options for Every Project (2026).
Step-by-Step: Cutting a Curve with a Template
- Make the template. Cut the shape from 1/4-inch or 3/8-inch plywood or MDF. Sand the edges smooth, since every bump gets copied into your workpiece.
- Attach the template to the blank. Use double-sided tape or screws placed outside the final cut line. Keep the template flush with the workpiece over the entire path.
- Select a pattern bit. A flush-trim bit with a top bearing works well when the bearing rides on the template and the cutting edge sits below it. Match the bearing diameter to the template offset you planned.
- Set the depth. Take multiple passes. A common approach is to remove no more than about 1/4 inch per pass in hardwood, going deeper only after the previous pass is clean.
- Feed against the rotation. Move the router counterclockwise around the outside of an external curve, and keep the bearing firmly against the template the whole time.
- Clean up the edges. Inspect for burn marks or tearout and follow with a sanding block or a small-radius file.
Setup Factors That Affect Curve Quality
Several settings control how smooth your curve turns out. Use the table below as a quick reference when planning a cut.
| Factor | What to Check | Effect on the Curve |
|---|---|---|
| Bit rotation direction | Feed against rotation | Prevents the router from pulling away from the template |
| Depth per pass | Shallow passes in hardwood | Reduces burning and tearout |
| Feed speed | Steady, not rushed | Keeps the bearing in constant contact |
| Grain direction | Read the grain before cutting | Reduces splintering on tight radii |
| Template smoothness | Sanded, with no flat spots | Determines how smooth the final edge is |
Tight curves with a small radius are harder than gentle arcs. If the radius is smaller than the bit’s cutting diameter, you will not be able to follow the path cleanly, so either use a smaller bit or cut the curve in stages.
Common Mistakes to Avoid
- Taking too deep a cut in one pass, which causes burning and bit deflection.
- Feeding with the rotation instead of against it, which can make the router grab and jump.
- Skipping template sanding, so every flaw shows up in the finished part.
- Letting the bearing lose contact with the template at the start or end of the cut.
- Routing end grain or very short-grained areas without backing material, which invites chipping.
Recommended gear
A template-cutting pattern bit with a top bearing is the core tool for this work, and it is worth matching the bearing diameter to your template plan. A plunge router with a fine depth adjustment makes it easier to take shallow passes without guessing. A router circle-cutting jig is useful if your project calls for consistent arcs. View on Amazon View on Amazon View on Amazon
Related Reading
If you want to build a fixed setup for repeat curved parts, read Wood Router Table Combo: How to Choose and Build One Step by Step (2026). For edge profiles that follow a curve, see How to Bevel Wood with a Router: 7 Best Picks Compared for 2026. Those working with templates on larger pieces may also find How to Flatten a Wood Slab with a Router: A Step-by-Step Guide useful.
FAQ
Can I cut a curve with a router without a template?
You can, using a bit with a bearing and careful freehand control, but accuracy is much lower. A template or jig gives repeatable results, especially for shapes you plan to duplicate.
Which direction should I feed the router for a curve?
Feed against the bit’s rotation. On an outside curve this usually means moving counterclockwise, which keeps the bearing pressed against the template.
How deep should each pass be when routing a curve in hardwood?
A common practice is about 1/4 inch per pass in hardwood, with deeper material removed over several passes. Shallow passes reduce burning and tearout.
Conclusion
Cutting curves with a router is mostly about preparation: a smooth template, the right pattern bit and a steady feed against the rotation. Work in shallow passes, check the grain and sand the template first, and your curves will come out cleaner. Consult a professional or the tool manufacturer’s manual if you are unsure about setup or safe operation.
