Updated November 2026
You can make grooves in wood without a router by sawing the walls of the groove, then removing the waste with a chisel, a backsaw, or a table saw with a dado blade. Each method produces a clean, flat-bottomed groove suited to shelves, panels and drawer bottoms. The right choice depends on the groove width, the depth and the tools already in your shop.
Mark the Groove Before You Cut
Start by setting the groove width. Measure the thickness of the board that will sit in the groove, usually 1/4 inch for drawer bottoms or 3/4 inch for shelves, and add a few thousandths for a snug but workable fit. Transfer the width to the board with a marking gauge or a pencil and a combination square. Then mark the groove location with a pencil line on the face and a second line on the end grain if the groove runs across the board.
Shopping for one? See our guide: 5 Best Wood Router Prices: How Much Is a Wood Router? 5 Picks Compared.
Method 1: Saw the Walls, Then Chisel the Waste
This is the most common hand-tool approach. Clamp the board to the bench and use a backsaw or a dovetail saw to cut down both walls of the groove to the full depth. Stay just outside the waste side of your line so the final width is slightly generous. Next, set a chisel of matching or slightly narrower width at the groove start and tap it with a mallet to remove waste in shallow bites, working from both ends toward the middle. Pare the bottom flat with a wider chisel to finish.
Method 2: Use a Table Saw With a Dado Stack
A table saw fitted with a dado stack cuts a groove in one pass, which makes it the fastest option for long, repeated grooves. Set the blade height to the groove depth, usually no more than half the board thickness for strength. Adjust the width with the chippers until the groove matches your mark, and test on a scrap of the same thickness. Run the board with the fence set so the groove lands where you want it. If you want more background, see How to Use a Belt Sander Without Gouging the Wood.
- Keep the blade guard and riving knife in place when possible, or use a sled for safety.
- Make the cut in one smooth pass and avoid stopping mid-cut.
- Check the fit with your actual panel before cutting the full set.
Method 3: Make Multiple Saw Passes on a Table Saw
If you do not have a dado stack, you can make a groove with a standard blade by making several passes. Set the blade to the groove depth and cut one kerf on each side of the groove line using the fence. Then remove the waste by making additional passes, moving the fence a blade width at a time. Shift the board in small steps and check the width frequently. The bottom will be slightly ridged, so smooth it with a block plane or a sanding block.
Method 4: Clean Up With a Plane or File
Whatever method you use, the groove bottom often needs refinement. A shoulder plane or a rabbet plane can clean the walls and square the corners. A small file or card scraper works well for uneven bottoms. Test the fit as you go and aim for a panel that slides in with light hand pressure rather than forcing it.
Common mistakes
- Cutting the groove wider than the panel, which leaves a loose, rattling joint.
- Going too deep and weakening the board edge, especially on thin stock.
- Chiseling against the grain and tearing out the groove edges.
- Forgetting to account for wood movement when a groove runs across the grain.
- Skipping a test cut on scrap before working the final piece.
Recommended gear
- Backsaw: A fine-tooth backsaw gives you a controlled, straight wall cut. View on Amazon
- Bench chisel set: A set with several widths lets you match the groove width and pare the bottom. View on Amazon
- Dado stack for table saw: A dado set cuts clean grooves in one pass on a table saw. View on Amazon
For more on groove-cutting methods, see How to Groove Wood Without a Router: 4 Methods That Work. If you later decide to cut grooves with power tools, How to Cut Grooves in Wood with a Router: A Step-by-Step Guide covers the router approach in detail, and How to Use a Wood Router Table: A Step-by-Step Guide for Beginners explains setup for repeated work.
FAQ
Can I cut a groove with just a hand saw?
Yes. A backsaw can cut both walls of the groove, and a chisel can remove the waste between them. This works well for narrow grooves in softer hardwoods or pine.
How deep should a groove be?
For most panels, a groove about one-third to one-half the thickness of the board is a common guideline. Going deeper weakens the edge, so stay within that range when possible.
Do I need a dado blade to cut grooves on a table saw?
No. You can make a groove with a standard blade using multiple passes, though a dado stack is faster and gives a flatter bottom.
Conclusion
Hand tools and a table saw both produce strong, accurate grooves without a router. Mark carefully, test on scrap, and match the groove width to your panel. With a little practice, these methods will serve most shelf, drawer and panel projects well.
