Updated November 2026

To router numbers into wood, you set up a template or guide, choose a bit that matches the depth and style you want, and cut each digit in a series of shallow passes. The result is crisp, evenly spaced numbers that work well on house signs, mailboxes, cutting boards and address plaques. This guide covers the method, the setup and the mistakes that most often ruin a good piece.

What You Need Before You Start

Gather everything before you power up the router so you are not stopping mid-cut to search for a clamp or a bit. A simple setup covers most projects.

Shopping for one? See our guide: 5 Best Wood Router Prices: How Much Is a Wood Router? 5 Picks Compared.

  • A plunge router or fixed-base router with a stable base
  • A straight or V-groove bit sized to your stroke width (1/4-inch straight bit is common for numbers 2 to 3 inches tall)
  • A number template, either a store-bought stencil or one you cut from 1/4-inch plywood or MDF
  • A template guide with a collar that matches your bit
  • Stock at least 3/4 inch thick, flat and free of cupping
  • Double-sided tape or clamps to hold the workpiece and template
  • Safety glasses and hearing protection

If you plan to make several signs, the workflow in How to Make Wood Signs with a Router: A Step-by-Step Guide for Beginners shows how to batch the setup. For letters, the same logic applies, as described in How to Router Letters in Wood: A Step-by-Step Guide for Beginners.

Step 1: Build or Choose the Template

The template determines the shape and spacing of every digit, so measure carefully. Print or draw the numbers at full size, then transfer them to your template material. Cut the openings slightly larger than the finished digit, based on the offset between your guide collar and bit. A typical guide-to-bit offset is the difference between the collar radius and the bit radius. Test the template on scrap before committing to the final board.

Step 2: Set Bit Depth and Make Shallow Passes

Never try to cut a full-depth groove in one pass. Set the bit to remove no more than about 1/8 inch per pass in hardwood, and repeat until you reach your target depth. A common target for signs is 1/8 to 1/4 inch. Shallow passes reduce burning, prevent tear-out and keep the bit from deflecting, which is the main cause of wobbly edges.

Feed Direction and Speed

Route in a counterclockwise direction around the outside of each digit, so the bit pulls the template guide against the stop. Move steadily, but do not force the router. If you hear the motor bog down or see scorch marks, slow the feed and check that the bit is sharp.

Step 3: Clean Up and Finish

Once every digit is cut to depth, remove the template and inspect the corners. Inside corners of rounded digits, such as the loop of a 6 or 9, often need a light touch with a chisel or a small file. Sand lightly with 150-grit paper, avoiding the crisp edges of the grooves. Fill the cuts with paint or stain as the project requires, wiping away excess from the surface before it dries.

Common Mistakes

  • Skipping the test cut on scrap, which hides template spacing errors until the final piece is ruined
  • Taking too deep a pass, causing burning, chatter and loose-fitting grooves
  • Letting the template shift, so use firm clamps or double-sided tape
  • Using a dull bit, which tears the wood instead of cutting clean walls
  • Routing against the rotation, which can pull the router out of your hands
  • Template guide kit: A set of guide collars helps you match the offset to the bit you are using, which makes the template dimensions more predictable. View on Amazon
  • Straight router bit: A straight bit with a 1/4-inch shank gives clean, flat-bottomed grooves in most hardwoods. View on Amazon
  • Clamps: Quick-release clamps keep the template and workpiece locked down throughout multiple passes. View on Amazon

FAQ

Can I router numbers into softwood?

Yes, but softwoods like pine tear out more easily and can fuzz at the edges. Use a sharp bit, shallow passes and a light sanding afterward for cleaner results.

What depth should I cut for outdoor signs?

Many builders cut 1/4 inch deep for outdoor numbers so paint or stain has room to fill the grooves without wearing through too quickly. Check your finish manufacturer’s recommendations for coverage.

Do I need a router table for this job?

No. A handheld router with a template guide works well for numbers. A router table is useful for repeated pieces, but it is not required.

Conclusion

Routing numbers into wood comes down to a solid template, a well-matched guide and bit, and shallow, controlled passes. Test each step on scrap and take your time on the inside curves. With a little practice, you can produce clean, durable numbers for any project.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.