Updated November 2026
To router a slot in wood, you clamp a straight guide to the workpiece, set a straight bit to the correct depth, and cut the slot in several shallow passes. The result is a clean, flat-bottomed groove that holds a panel, shelf or divider snugly. The steps below cover setup, cutting technique and the mistakes that most often ruin a slot.
Choose the Right Bit and Setup
A straight bit matching the width of your slot is the simplest choice. Its diameter defines the slot width, so a 1/4-inch bit cuts a 1/4-inch slot. Use a router with a collet that holds the shank firmly, and keep the bit as short as practical to reduce deflection. For a slot that accepts a 1/4-inch plywood panel, expect to cut a true 1/4-inch width; if you need a snug fit, test the bit on scrap first, since bit diameters can vary slightly from their stated size.
Shopping for one? See our guide: 5 Best Wood Router Prices: How Much Is a Wood Router? 5 Picks Compared.
Your guide matters as much as the bit. A straight edge or a clamped straightedge keeps the cut parallel to the edge of the board. Measure from the bit’s cutting edge to the router base’s guide edge, then clamp the straightedge at that offset so the slot lands exactly where you want it.
Set Depth and Mark the Layout
Mark the start and end points of the slot on the workpiece with a sharp pencil. Mark them clearly, because the cut must stop short of or exactly at these lines. Set the bit depth in passes rather than in one go. For a typical 3/8-inch-deep slot, a reasonable approach is to make three passes: roughly 1/8 inch, then 1/4 inch, then the final 3/8 inch.
Test the depth on a scrap piece of the same thickness. Check the slot against the panel or part it will hold. A slot that is too tight can split the surrounding wood, while one that is too loose will rattle.
Cut the Slot in Passes
- Clamp the workpiece flat to the bench, with the clamps away from the router’s path.
- Clamp the straightedge guide at the offset you measured.
- Set the bit to the first depth, about 1/8 inch.
- Start the router with the base flat on the guide and the bit away from the wood. Let it reach full speed.
- Feed the router left to right (or in the direction that keeps the bit’s rotation pushing against the guide), moving steadily.
- Stop at your marked end point, switch off, and wait for the bit to stop before lifting it.
- Repeat for each deeper pass, adding roughly 1/8 to 1/4 inch per pass.
- Square the ends of the slot with a chisel if the router leaves rounded corners.
Feed Direction and Speed
Feed against the bit’s rotation so the cutter pulls into the guide and the wood. A steady feed rate is better than a fast one. If the router bogs down or the cut burns, slow the feed. If the cut tears out, reduce the depth of each pass.
Finish the Slot
Once the final pass is complete, check the bottom of the slot for flatness and smoothness. A light sweep with a sharp chisel can clean up any ridges left by the bit. Test-fit the panel before gluing or assembling anything, since wood movement and small differences in bit size can change the fit.
Common Mistakes
- Cutting the full depth in one pass, which causes tear-out and strains the router.
- Skipping the scrap test, so the slot ends up too tight or too loose.
- Letting the guide shift during the cut, which produces a wandering slot.
- Stopping the router before the bit clears the wood, leaving a gouge at the end.
- Feeding too fast, which leaves ridges and burn marks.
Recommended Gear
- A straight-cutting router bit set: Having several diameters on hand lets you match the slot to different panel thicknesses without rebuying. View on Amazon
- A clamping straightedge guide: It keeps the router running true along the layout line, which is the single biggest factor in a straight slot. View on Amazon
FAQ
Can I cut a slot in one pass?
You can on thin, soft wood with a small bit, but multiple passes are safer and cleaner for most slots. Shallow passes reduce burning, tear-out and strain on the router.
What is the best bit for a slot?
A straight bit sized to your panel thickness is the standard choice. It cuts a flat-bottomed slot with square sides.
How do I keep the slot straight?
Clamp a straightedge guide at the correct offset from the bit and keep the router base pressed against it throughout the cut.
Conclusion
Routing a slot comes down to three things: the right straight bit, a clamped guide that holds the line, and shallow passes that let the cutter work cleanly. Test on scrap, check your fit, and the slot will hold its panel accurately. For more techniques, see How to Notch Wood with a Router: A Step-by-Step Guide for Beginners for related cuts.
Related reading
- Wood Thread Cutting Router Bit: How to Cut Threads in Wood with a Router
- Wood Router Table Combo: How to Choose and Build One Step by Step (2026)
- Wood Router Price in Kenya: What to Expect and How to Buy in 2026
- Wood Router Price in India: What You'll Pay and How to Choose (2026)
- Wood Router Made in USA: How to Choose a Domestic Router (2026)
