Updated November 2026

Red barn birdhouse plans give you a small, classic nest box shaped like a miniature barn, with a gabled or gambrel roof, a front entry hole, and a front panel that opens for cleaning. This guide walks through a basic build using 3/4-inch cedar or pine, a cut list you can take to the saw, and the dimensions that keep songbirds safe and dry. You can finish the project in one afternoon with basic tools.

Gather Materials and Cut Your Parts

Cedar is the most common choice because it resists rot without paint. A 1×6 board about 5 feet long is enough for the whole house. Cut the following pieces before you start assembly:

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Two side walls: 1-1/2 in × 6 in × 9 in, with the top edges cut at a 45-degree slope to meet the roof
  • Front and back walls: 3/4 in × 5-1/2 in × 9 in, with a 1-1/2 in entry hole drilled 6 in from the bottom of the front panel
  • Floor: 4 in × 4 in, with four 1/4 in drain holes
  • Two roof panels: 3/4 in × 5 in × 7 in, mitered at the ridge
  • One front door panel: 3/4 in × 5-1/2 in × 9 in, held by a single screw at the top

Label each piece on the back as you cut. Barn plans have more angled cuts than a standard box, and mixing up the side and front pieces is the most common reason builds stall.

Assemble the Walls and Floor

Start with the floor. Set it between the side walls so the bottom edges are flush, then drive two 1-1/4 in exterior screws through each side into the floor edges. Pre-drill every screw hole to prevent splitting cedar near the ends. Attach the front and back walls to the sides the same way, keeping the top edges square so the roof will sit flat.

Check the box with a square before the glue or screws set. A house that is out of square by 1/8 inch will show a visible gap at the roof seam.

Build and Attach the Roof

Cut the roof panels to a 45-degree miter where they meet at the ridge. Glue the joint with exterior wood glue and clamp it, or fasten it with two screws driven from the underside. Position the roof over the top of the walls so it overhangs about 1 inch on each side. This overhang sheds rain away from the entry hole. Secure the roof with 1-1/4 in exterior screws driven down through the roof into the wall tops.

Add the Entry Hole, Door and Ventilation

Drill the entry hole with a Forstner bit or hole saw, using the size recommended for your target species. A 1-1/2 in hole suits house wrens and chickadees, while bluebirds usually need 1-9/16 in. Sand the edge of the hole lightly so birds are less likely to be cut.

Attach the front door with one screw at the top so it swings open for cleaning. Drill two 3/8 in ventilation holes near the top of the side walls, under the roof overhang, to let heat and moisture escape. Finish with an exterior stain or no finish at all. Leave the inside rough and unpainted.

Mounting and Placement

Mount the house 5 to 10 feet off the ground on a pole or post, facing away from prevailing winds and direct afternoon sun. Clear a 25-foot zone around the box so predators have fewer perches nearby. Check that nest boxes are rated for the species you want, since entry hole size controls which birds can use the house.

Common Mistakes

  • Using treated lumber, which can release chemicals harmful to nesting birds
  • Skipping drain holes in the floor, which lets water pool and rot the nest
  • Making the entry hole too large, which invites starlings and sparrows that take over nests
  • Painting the inside, which traps heat and fumes
  • Mounting the box in full sun, where chicks can overheat

A Forstner bit set makes clean entry holes in cedar without tear-out, and it is the most useful upgrade for this build. View on Amazon

A combination square helps you keep the walls and roof square during assembly. View on Amazon

Exterior wood screws resist rust and cedar’s natural acids better than standard drywall screws. View on Amazon

FAQ

What wood is best for red barn birdhouse plans?

Cedar and untreated pine are the most common choices because they resist weather and are safe for nesting birds. Avoid pressure-treated lumber.

What size entry hole should I drill?

The entry hole size depends on the species you want to attract. House wrens and chickadees use about 1-1/8 in to 1-1/2 in holes, while bluebirds usually need about 1-9/16 in.

When should I clean out the nest box?

Clean the box after each nesting season to remove old nesting material and parasites. Open the front door for cleaning and do not disturb an active nest.

Conclusion

With the cut list, assembly order and placement tips above, you can build a sturdy red barn birdhouse in an afternoon. Choose untreated cedar, size the entry hole for your target bird, and mount the box where it stays shaded and out of prevailing wind. For more designs, browse our Barn Style Birdhouse Plans: A Step-by-Step Build With Cut List and Barn Owl Birdhouse Plans: A Step-by-Step Build Guide.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.