Updated November 2026
Scroll saw birdhouse plans give you a small, good-looking nest box you can cut, sand, and assemble in a single afternoon. This guide walks through a simple cedar design with a front-opening panel, a fixed floor, and a scroll-cut entrance hole sized for chickadees and wrens. You will finish with a box that holds up to weather and gives birds a dry, safe place to nest.
Cut List and Materials
Use 3/4-inch cedar or another rot-resistant board that measures about 5-1/2 inches wide. Cedar is light, stable, and does not need paint. Cut the following pieces, which are based on a standard box for small cavity nesters:
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
- Front and back: 2 pieces, 5-1/2 x 9-1/2 inches (back may be slightly taller for a roof overhang)
- Sides: 2 pieces, 5 x 8 inches, with the top edge beveled to match the roof slope
- Floor: 1 piece, 4-3/4 x 4-3/4 inches
- Roof: 1 piece, 6 x 7 inches, hinged or screwed on for access
- Hardware: exterior screws, 1-1/4-inch galvanized or stainless, plus a few corrosion-resistant hinges
Cutting the Pieces on a Scroll Saw
A scroll saw is the right tool for the entrance hole and any decorative curves, but it is not the best choice for long, straight rip cuts. Do your straight cuts on a table saw or with a hand saw first, then move to the scroll saw for detail work.
- Mark the entrance hole on the front panel, centered about 6 inches from the floor. For chickadees, use a 1-1/8-inch diameter; for wrens, 1-1/4 inches.
- Drill a pilot hole inside the marked circle so the blade can enter.
- Thread a fine-tooth (10 to 15 TPI) blade through the pilot hole and cut the circle smoothly, turning the workpiece slowly rather than forcing it.
- If you want a decorative edge, cut the roof or front panel top with a gentle arc. Keep the arc shallow so the box stays weather-tight.
Assembly and Finishing
Dry-fit every piece before you drive any screws. Check that the sides sit square to the floor and that the roof overhangs the front by about 1 inch to shed rain. Drill pilot holes near the edges to prevent splitting in cedar.
Assembly Sequence
- Attach the floor to the back panel first, then add the sides.
- Screw the front panel in place so it can be removed later for cleaning. Use two screws per side at most.
- Attach the roof with hinges or screws, depending on how you want to access the box each fall.
- Drill four to six 1/4-inch drainage holes in the floor and a few small ventilation slots near the top of the sides.
Leave the cedar unfinished. Bare cedar weathers gray over time and is safe for birds. Avoid paint, stain, or sealers on the inside or the entrance area.
Mounting Location and Timing
Mount the box 5 to 10 feet off the ground on a post or tree trunk, facing away from prevailing winds and direct afternoon sun. Build and hang the box in late winter so birds can claim it before spring nesting starts. Check that the box is stable and that the entrance has no branches blocking the flight path.
Common Mistakes
- Cutting the entrance hole too large, which lets starlings and house sparrows in and crowds out smaller birds.
- Skipping drainage holes, which leads to damp nests and mold.
- Using pressure-treated lumber or painted wood, which can release chemicals that harm nesting birds.
- Forcing the scroll saw blade, which causes it to bind, break, or tear the cedar.
- Mounting the box too low, where cats and raccoons can reach it.
If you want more detailed layouts for different species, see Wren Birdhouse Plans Free: Build a Cedar House in One Weekend and Plans for Wren Birdhouse: A Step-by-Step Guide With Cut List. For a larger opening, compare Tree Swallow Birdhouse Plans: A Step-by-Step Build Guide and Plans for a Bluebird Birdhouse: Build One in a Weekend.
Recommended Gear
- Scroll saw with a variable-speed control: Lets you slow down for tight curves in cedar and reduce tear-out. View on Amazon
- Fine-tooth scroll saw blades: Narrow blades make clean entrance holes and reduce burn marks on softwood. View on Amazon
- Stainless or galvanized exterior screws: Resist rust from rain and cedar tannins, so the box lasts through many seasons. View on Amazon
FAQ
What wood is best for scroll saw birdhouse plans?
Cedar is the most common choice because it resists rot, stays stable, and needs no finish. Pine works too, but it should be untreated and sealed only on the outside.
What size hole should I cut?
Use about 1-1/8 inches for chickadees and 1-1/4 inches for wrens. Larger holes invite starlings and sparrows, which often displace native cavity nesters.
Do I need a scroll saw to build this box?
No. You can drill the entrance hole with a hole saw and cut the rest with a hand saw or table saw. A scroll saw simply makes curved and detail cuts easier.
Conclusion
Following these scroll saw birdhouse plans gives you a sturdy cedar nest box with a correctly sized entrance and proper drainage. Mount it high, keep it clear of predators, and check it each season. With a little care, it can host birds for many years.
