Updated November 2026
Wood projects with router work go faster and look cleaner when you set up the tool correctly and make shallow passes. This guide walks you through the core setup, cutting order and finishing steps so you can rout edges, dados and profiles on your own workpieces. Most beginners can handle these basics with a fixed-base router and a few common bits.
Set Up Your Router and Workpiece
Start by choosing the right router for the job. A fixed-base model suits most tabletop work, while a plunge router is better for mortises and stopped cuts. Clamp your workpiece firmly to a bench or a sacrificial base so it cannot shift under the bit.
Shopping for one? See our guide: 6 Best 4×4 CNC Wood Router Machines for Big Projects in 2026.
Next, install the bit with at least three-quarters of its shank inside the collet. Tighten the collet fully, then check that the bit spins true by hand before you turn the router on.
Make Your Cuts in the Right Order
Routing removes a lot of material quickly, so take it in stages. For most projects, a depth of 1/4 inch or less per pass keeps the router stable and reduces burning. Work in two or three passes for anything deeper than that.
- Rout the end grain first, moving left to right against the bit’s rotation.
- Rout the long grain second to clean up any tear-out left by the end grain cut.
- Cut the edge profile last, which hides any chipping at the corners.
- Sand lightly with 180-grit paper to remove any remaining fuzz or burn marks.
Choose Bits and Feed Rates by Project
Bit choice depends on what you are building. Straight bits handle dados and grooves for shelves and cabinets, while round-over and chamfer bits suit table edges and decorative trim. Match the bit diameter to your router’s collet capacity and the material thickness you plan to cut.
Feed rate matters just as much as bit choice. Move the router steadily enough that it sounds like a continuous cut, not a squeal or a stall. If the wood smokes or the bit grabs, slow down and reduce the depth of cut.
| Project Type | Common Bit | Typical Passes |
|---|---|---|
| Shelf dados | Straight bit | 2 to 3 |
| Table edges | Round-over bit | 2 |
| Picture frame profiles | Ogee or cove bit | 2 to 3 |
| Decorative trim | Chamfer bit | 1 to 2 |
Common Mistakes to Avoid
- Taking one deep pass instead of several shallow ones, which overheats the bit and causes burning.
- Routing against the bit’s rotation, which can kick the router back toward you.
- Skipping a test cut on scrap wood before working on your finished piece.
- Using dull bits, which tear the grain and leave rough edges.
- Forgetting to unplug the router when changing bits.
If you are new to routing, read up on the basic bit types before buying a full set. Our guide to 5 Best Router Bits for Wood Compared for Every Project (2026) compares the most useful options. You can also review 4 Best Wood Router Bit Shapes for Every Project (2026) to see which profiles fit common builds.
Recommended Gear
- Fixed-base router: A stable platform for edge profiles and dados on flat stock. View on Amazon
- Straight bit set: Covers most dado and groove work for shelves and cabinet parts. View on Amazon
- Bench clamps: Hold your workpiece steady so the bit does not chatter or shift. View on Amazon
FAQ
How deep should each router pass be?
Most woodworkers keep each pass to about 1/4 inch or less. Shallower passes reduce burning and make the router easier to control.
Which direction should I feed the router?
Feed the router against the direction the bit spins, which is left to right on a standard fixed-base setup. Feeding with the spin can pull the tool out of your hands.
Do I need a router table for these projects?
A router table helps with small pieces and repeatable profiles, but a handheld fixed-base router works well for most edge and dado cuts on larger stock.
Conclusion
With a solid setup, the right bit and shallow, controlled passes, you can complete most wood projects with router work cleanly. Practice on scrap wood first, then move on to your finished pieces. Each project will build your confidence and your technique.
