Updated November 2026
Woodworking patio chair plans give you a clear path from rough lumber to a chair that handles rain, sun and daily use on a deck or porch. This guide walks through the proportions, cut list and joinery for a simple slat-back armchair, then covers the finish that keeps it standing for years. Expect a build that takes a weekend once your stock is milled.
Choose Wood and Set Your Dimensions
For outdoor furniture, pick a rot-resistant species. Western red cedar, black locust and teak are common choices, and pressure-treated pine works for budget builds if you seal it well. Aim for a seat height of about 17 to 18 inches and a seat depth of 18 inches, with a back angle of roughly 100 degrees from the seat for comfort.
Shopping for one? See our guide: Quilt Rack Plans Woodworking: 4 Best Builds for Beginners (2026).
Cut List and Joinery
Mill all stock to 3/4-inch thickness. The core parts for one chair are:
- 2 front legs, 1-1/2 x 1-1/2 x 27 inches
- 2 back legs, 1-1/2 x 1-1/2 x 35 inches
- 2 side rails, 1-1/2 x 3-1/2 x 18 inches
- 2 front seat rails, 1-1/2 x 3-1/2 x 21 inches
- 2 back seat rails, 1-1/2 x 3-1/2 x 21 inches
- 6 seat slats, 1-1/2 x 3-1/2 x 21 inches
- 2 arm supports, 1-1/2 x 1-1/2 x 9 inches
- 2 armrests, 1-1/2 x 3 x 16 inches
- 5 back slats, 3/4 x 2-1/2 x 22 inches
Cut mortise-and-tenon joints where the rails meet the legs. A 3/8-inch tenon, about 1-1/4 inches long, gives strong shoulders against racking. Dry-fit every joint before glue-up, and check that the frame sits square by measuring diagonals. Equal diagonals mean a square frame.
Assembly Sequence
- Assemble the side frames first: legs, side rails and arm supports.
- Join the two side frames with the front and back seat rails.
- Fit the seat slats with a 1/4-inch gap between them for drainage.
- Attach the back legs to the back slats, then fit the armrests.
Shape, Sand and Finish
Round the arm edges and the top of each back slat with a router and a 1/4-inch roundover bit. Sand progressively through 120 and 180 grit. Use stainless or hot-dipped galvanized screws for any fasteners, since ordinary steel will stain the wood and corrode.
Apply a penetrating exterior oil or a marine-grade spar varnish. Plan on re-coating every year or two in full sun. Let each coat dry as the product label specifies before the next.
Common Mistakes
- Skipping the diagonal check, which leaves the chair rocking on uneven decking.
- Gluing slats tight together, so water pools and rots the seat.
- Using untreated pine or interior finishes outdoors.
- Cutting tenons too short, which weakens the joints under load.
Recommended Gear
A router with a roundover bit makes quick work of the arm and slat edges. View on Amazon
A combination square helps you check the frame and cut tenon shoulders accurately. View on Amazon
Stainless exterior screws resist rust and staining on outdoor furniture. View on Amazon
FAQ
What wood is best for outdoor patio chairs?
Cedar, black locust and teak resist rot and insects naturally. Pressure-treated pine is a workable alternative if you seal it thoroughly.
Do I need mortise-and-tenon joints?
They are the strongest option for chairs that take daily loads. Dowels or screws with glue can work for lighter builds, but expect more movement over time.
How often should I refinish an outdoor wood chair?
In full sun, plan on a fresh coat of oil or spar varnish every one to two years. Shaded chairs may go longer between coats.
Conclusion
With the right species, a tight mortise-and-tenon frame and stainless fasteners, these woodworking patio chair plans produce a chair built to last outside. Check your joints for square before glue-up, and keep the finish fresh. For more outdoor builds, see Outdoor Chair Woodworking Plans: A Step-by-Step Build Guide.
