Updated November 2026
Woodworking plans for a gun rack give you a clear path to a sturdy, wall-mounted rack that holds rifles and shotguns securely at home. In this guide you will work out the dimensions, cut the parts, join them with dependable joinery and finish the rack so it lasts. The project suits a weekend build with basic hand and power tools.
Plan the Rack Before You Cut
Start by measuring the longest firearm you plan to store, including the stock and barrel, and add about 4 inches of clearance on each end. A rack for two rifles typically ends up around 36 to 42 inches wide. Decide whether the rack will hold rifles muzzle-up or horizontal, because that changes the height of the cradles and the depth of the base.
Shopping for one? See our guide: Quilt Rack Plans Woodworking: 4 Best Builds for Beginners (2026).
Sketch the layout on paper first. Mark the position of each cradle, the mounting cleat and any storage shelf or drawer. If you are not sure how the parts fit together, a related build such as the Woodworking Plans Gun Cabinet: A Step-by-Step Build Guide for Beginners shows how enclosed storage differs from an open rack.
Build the Base and Cradles
Choose a stable hardwood or plywood with no warping. Cut the back board, the base and the cradle blocks to the sizes in your plan, and cut the cradle notches with a jigsaw or table saw so each firearm rests on a padded or felt-lined surface rather than bare wood.
- Mark cradle centers at equal intervals across the back board.
- Cut each cradle notch slightly wider than the stock width, then test-fit a rifle.
- Glue and clamp the cradles to the base, checking square with a framing square.
- Drill pilot holes and add screws from the back for a clean front face.
Join the Parts With Strong Joinery
Rack joints take steady loading, so favor joinery over butt joints held only by screws. Rabbet or dado joints work well for attaching the base to the back board, and a mortise-and-tenon or dowel joint suits the cradle supports. Dry-fit every joint before glue goes on, and check that the rack sits flat against the wall.
Use a router with a straight bit to cut dados cleanly. A router table makes repeatable dados easier, and a featherboard keeps the stock tight to the fence.
Mount, Finish and Protect
Mount the rack into wall studs using lag screws, not drywall anchors. Locate studs with a stud finder, and use a cleat or ledger board sized to the rack’s weight. Before mounting, sand all surfaces through 180 grit and apply a finish such as a penetrating oil or a clear polyurethane. Keep finish off the cradle padding so the rifles do not pick up residue.
Common Mistakes
- Mounting into drywall alone, which will not hold a loaded rack.
- Cutting cradles too tight, which can scratch stocks or stress the wood.
- Skipping a dry fit, leading to gaps and out-of-square assembly.
- Placing the rack where firearms are exposed to direct sun or moisture.
- Storing ammunition on the same shelf as firearms, which is best avoided.
Recommended Gear
- Router with a straight bit set: Useful for clean dados that lock the base and back together. View on Amazon
- Clamps in several lengths: Hold cradles square during glue-up so joints close fully. View on Amazon
- Felt or foam self-adhesive padding: Protects finished stocks from the cradle surface. View on Amazon
FAQ
What wood is best for a gun rack?
Hardwoods such as oak or maple are durable and hold screws well. Quality plywood also works and resists warping in a wall-mounted rack.
Can I mount a gun rack into drywall?
No. Fasten the rack into wall studs with lag screws, since drywall anchors cannot safely carry the weight of loaded firearms.
How many rifles should one rack hold?
Most home racks hold two to four long guns. Size the base and cradle spacing to your firearms, and consult a professional if you plan a heavier installation.
Conclusion
With a clear plan, accurate cuts and solid joinery, you can build a rack that holds your firearms safely and looks good in the room. Confirm your wall structure before mounting. For more build ideas, explore other projects in the woodworking plans collection.
