Updated November 2026

Planing wood with a router lets you flatten rough boards, cupped panels and thick slabs without a jointer or thickness planer. You will set up a sled, choose the right bit and make shallow passes that leave a flat, smooth face ready for finishing. The method works well for wide stock that would not fit a benchtop planer.

What You Need Before You Start

Gather the right tools so the cut stays safe and even. Most setups use a fixed-base router, a straight or surfacing bit, and a sled that rides on the high spots of the workpiece.

Shopping for one? See our guide: 6 Best Planing Jigs for a Wood Router Options for Flattening Slabs (2026).

  • A fixed-base or plunge router with at least 1-1/2 horsepower, mounted in a router table or hand-held on a sled
  • A surfacing bit with a bearing-guided or flush-cut design, or a straight bit of 1/2-inch shank
  • Two parallel rails or a flat sled base, at least 2 inches wider than the router base
  • Double-sided tape or shims to hold the stock flat on the bench
  • Dust collection, eye protection and hearing protection

Setting Up the Router and Sled

Start by fixing the stock to your bench. Shim any rocking so the workpiece sits solid, and check it with a straightedge. Mount the router to the sled so the bit reaches across the full width of the board.

Set the bit depth to remove no more than 1/16 inch per pass on hardwoods. Softer woods like pine can handle slightly deeper cuts, but shallow passes keep tear-out and burning under control. Lock the depth stop once you have it right.

Making the Passes

Work from one end of the board to the other, keeping the router base flat on the sled rails at all times. Move steadily in the direction that minimizes tear-out, which is usually with the grain. Overlap each pass by about one-third of the bit diameter so no ridges remain.

Check progress after every few passes. Stop when the entire surface shows fresh cutter marks, which tells you the high spots are gone. Then flip the board if it is a panel and repeat on the other face.

Reading the Surface as You Go

Run a straightedge across the board between passes. Light reflecting under the edge marks a low area, and the sled will not reach it until the high spots drop. Keep cutting until the straightedge sits flat across the full length.

Surfacing Pass Settings at a Glance

Wood type Suggested depth per pass Feed direction
Softwood (pine, fir) Up to 1/8 inch Follow the grain
Medium hardwood (oak, maple) About 1/16 inch Follow the grain
Dense or figured hardwood 1/32 to 1/16 inch Read the grain before each pass

A surfacing bit with a bearing guide keeps the cut consistent when you run the sled over uneven stock. Look for one labeled as a surfacing or planing bit for router use. View on Amazon

A sturdy straightedge helps you check the surface between passes so you know where to cut next. View on Amazon

Double-sided tape designed for woodworking holds thin stock firmly without marring the face. View on Amazon

Common Mistakes to Avoid

  • Cutting too deep in one pass, which causes chatter, burning and an uneven surface
  • Feeding against the grain, which tears out fibers and leaves rough patches
  • Letting the sled tilt, so the cut ends up tapered instead of flat
  • Skipping the straightedge check, which hides low spots until late in the process
  • Ignoring dust collection, which can clog the bit and hide your progress lines

If you are building a larger shop jig, a few well-chosen designs can speed up the setup. See Wood Router Jig Plans: 5 Shop-Compared Designs You Can Build This Weekend for ideas, and check the Router Bit for Planing Wood: 6 Best Picks for Flattening Slabs (2026) guide if you need a bit recommendation.

FAQ

Can I plane a board with a router instead of a jointer?

Yes, a router sled can flatten a board’s face, though it is slower than a jointer for very long stock. It works best for wide slabs and panels that a jointer cannot handle.

What bit is best for planing wood with a router?

A surfacing bit with a bearing guide or a large straight bit is typical. The bearing keeps the cut even as the sled rides over high and low spots.

How deep should each pass be?

Keep passes to about 1/16 inch on hardwoods and slightly deeper on softwoods. Shallow passes reduce tear-out, burning and strain on the router.

Conclusion

Planing wood with a router gives you a flat, usable surface using tools many shops already own. Take shallow passes, follow the grain and check your progress with a straightedge. Once the surface is flat, you can move on to joinery or finishing with confidence.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.