Updated November 2026

Woodpecker birdhouse plans free of charge are easy to find, but the right dimensions matter more than the design. This guide gives you a simple, sized plan for a woodpecker-friendly nest box, a cut list, and the build steps that keep the cavity safe for the birds you want to attract. You can complete the project in one weekend with basic tools.

Choose the Right Dimensions for Your Woodpecker

Most cavity-nesting woodpeckers, including downy and hairy woodpeckers, do well in a box with a floor of about 4 by 4 inches and an interior height of 9 to 12 inches. The entrance hole should be 1¼ to 1½ inches across for downies and about 1½ to 1¾ inches for hairies. Larger species such as the red-headed woodpecker need a bigger cavity and a larger hole, so check the species before you cut.

Shopping for one? See our guide: 3 Best Free Printable Octagon Birdhouse Plans Frees (2026): Our Picks.

Mount the box 6 to 20 feet above ground on a dead tree or sturdy post. Woodpeckers prefer snags, so a rough, weathered surface is better than a smooth one.

Cut List and Materials

Use rough-sawn or rough cedar, pine or pressure-treated lumber without chemical treatment inside. Nominal ¾-inch stock is standard. Cut the pieces below from a single 1×6 board about 6 feet long.

Part Qty Dimensions
Front 1 ¾ x 5½ x 12 in
Back 1 ¾ x 5½ x 15 in (extends above for mounting)
Sides 2 ¾ x 4 x 12 in
Floor 1 ¾ x 4 x 4 in
Roof 1 ¾ x 6 x 7 in

Build Steps for a Solid, Predator-Resistant Box

  1. Cut all parts to the sizes above. Square the ends with a miter saw or table saw.
  2. Drill drainage holes, about ¼ inch, through the floor at each corner. Rough the inside faces of the front and back with a saw kerf or scoring tool so the young can climb out.
  3. Attach the sides to the floor with exterior wood glue and 1¼-inch galvanized or stainless screws. Pre-drill to prevent splitting.
  4. Fasten the front and back. Leave the front panel removable for cleaning by using two screws instead of glue.
  5. Mark and drill the entrance hole, 1¼ to 1½ inches across, centered about 7 to 9 inches above the floor. Use a Forstner bit for a clean edge.
  6. Attach the roof with a slight overhang on the front, and add a hinged or screwed-on panel for access. Seal the outside with exterior paint or a water-based stain, leaving the interior bare.

Finishing and Mounting Tips

Cover the roof with a simple metal flashing or tar paper to shed rain. Pre-drill mounting holes on the back panel, and use a stainless bolt or strap rather than nails so the box can be taken down for cleaning each fall. Mounting higher than 6 feet and facing the entrance away from prevailing winds usually improves occupancy.

Common Mistakes to Avoid

  • Using treated lumber, paint or varnish on the inside, which can harm nesting birds.
  • Drilling the entrance hole too large, which lets in starlings and larger predators.
  • Skipping drainage holes, leaving the floor wet and damp.
  • Mounting on a smooth pole without predator guards.
  • Making the box too shallow, which leaves chicks exposed to the weather.
  • Forstner bit set: Produces clean, flat-bottomed entrance holes that look finished and resist splitting. View on Amazon
  • Exterior wood glue: Holds the joints together through seasonal swelling and weather exposure. View on Amazon
  • Stainless steel exterior screws: Resist rust so the box stays secure and comes apart easily for annual cleaning. View on Amazon

If you plan to build several boxes, you may also want to compare designs. Our guide to Red Headed Woodpecker Birdhouse Plans Free: 5-Step Build Guide covers a larger cavity, and Pileated Woodpecker Birdhouse Plans: A Step-by-Step Build Guide shows the much bigger dimensions needed for the largest species. For smaller songbirds, Wren Birdhouse Plans Free: Build a Cedar House in One Weekend is a good companion project.

FAQ

What entrance hole size should I use for a woodpecker box?

Use 1¼ to 1½ inches for downy woodpeckers and about 1½ to 1¾ inches for hairy woodpeckers. Check your local species guide before cutting, since larger woodpeckers need bigger openings.

Where should I hang a woodpecker birdhouse?

Mount it 6 to 20 feet off the ground on a dead tree or sturdy post, facing away from prevailing winds. Woodpeckers prefer weathered, rough surfaces over smooth poles.

Should I paint the inside of the box?

No. Leave the interior bare and use only exterior finishes on the outside. Chemical residues inside can harm nestlings.

Conclusion

With the right dimensions, a simple cut list and a few careful steps, you can build a woodpecker box that stays safe and easy to maintain. Keep the entrance hole small, drill drainage holes, and mount it high on a solid support. Clean it out each fall so it is ready for the next season.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.