Updated November 2026

Simple wood birdhouse plans give you a sturdy nest box built from a single board, a few screws and basic hand tools. In this guide you will get a cut list, assembly steps and the details that keep chicks safe, so the finished house works for chickadees, nuthatches and wrens. Plan on about an afternoon of work once your wood is cut.

Materials and Cut List

Use a 1-inch-thick board of cedar, pine or cypress, roughly 5 to 6 feet long and 6 inches wide. Rough cedar is a common choice because it resists rot without paint. The house below is sized for small cavity nesters such as chickadees and wrens.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

Part Quantity Dimensions
Front and back 2 1 x 6 in. x 9 in. (front trimmed to 7 in. at the top angle)
Sides 2 1 x 5 in. x 8 in.
Floor 1 1 x 4 in. x 4 in.
Roof 1 1 x 6 in. x 7 in.

Step-by-Step Assembly

Cut the parts and drill the drainage holes

Cut each piece to the sizes above using a miter saw or a hand saw with a square guide. Drill four 1/4-inch drainage holes through the floor so rain runs out instead of pooling. Drill a few small ventilation holes near the top of each side panel.

Attach the sides and back

Set the back panel flat and align the two side panels flush with the top edge. Pre-drill and fasten each side with two 1 1/4-inch exterior screws. Keep the screws stainless or galvanized so they will not stain the wood over time.

Add the floor and front

Set the floor 1 1/2 inches up from the bottom edge so the walls overhang it slightly. This keeps the floor from trapping moisture. Attach the front panel with the entrance hole cut in it. Use a 1 1/8-inch hole for chickadees or a 1 1/4-inch hole for wrens.

Fit the roof

Attach the roof so it overhangs the front by about 1 inch and the back by about 2 inches. The overhang shades the entrance and sheds rain away from the seam. Use a hinge or a single screw on the back edge if you want to open the box for cleaning.

Common Mistakes and Tips

  • Skip paint, stain and varnish on the inside walls, since fumes and residue can harm nesting birds.
  • Do not add a perch. Predators use perches to reach the entrance, and birds do not need one.
  • Pre-drill every screw hole near the edges to prevent splitting in cedar and pine.
  • Mount the house 5 to 10 feet off the ground on a post or tree, facing away from prevailing winds.
  • Clean out old nesting material once a year, after the season ends.

A small hand drill and a set of spade-style bits make it easy to cut clean entrance holes without tearing the front panel.

View on Amazon

Exterior-rated stainless steel screws resist rust and prevent staining from tannins in cedar.

View on Amazon

A combination square helps you check that the sides and roof sit square before you drive the screws.

View on Amazon

If you want more ideas after this build, see Wood Birdhouse Plans Free: 6 Easy Builds With Cut Lists for additional designs, or Simple Cedar Birdhouse Plans: A Step-by-Step Build in One Weekend for another cedar version. Builders who want a species-specific box can check Wren Birdhouse Plans Free: Build a Cedar House in One Weekend or Tufted Titmouse Birdhouse Plans: A Step-by-Step Build Guide.

FAQ

What size entrance hole should a simple birdhouse have?

A 1 1/8-inch hole suits chickadees and titmice, while a 1 1/4-inch hole works for wrens. Larger holes let in starlings and other competitors, so stick to the size for the species you want.

What wood is best for a simple birdhouse?

Cedar, cypress and untreated pine are common choices because they resist moisture without chemical treatments. Avoid pressure-treated lumber, since preservatives can be harmful to birds.

When should I put up a birdhouse?

Most owners mount boxes in late winter or early spring, before nesting begins. Putting the box up early gives birds time to find it and claim the territory.

Conclusion

Simple wood birdhouse plans like these produce a durable nest box with a clean finish and no hardware that could harm birds. Follow the cut list, drill proper drainage and ventilation holes, and mount the house at the right height. With a little yearly cleaning, the box can host nesting birds for many seasons.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.