Updated November 2026

Cutting wood circles with router is one of the most reliable ways to get clean, accurate round parts for tabletops, lazy Susans, birdhouse roofs and clock faces. You set a pivot point, attach the router to a radius arm, and cut the circle in several shallow passes. This guide covers the setup, the cutting sequence and the mistakes that cause tear-out or wobbly edges.

Set Up the Circle Jig

Most router circles are cut with a trammel jig, which is a straight arm that holds the router at a fixed distance from a center pivot. Screw a sacrificial base board to your workpiece, then mark the center point. Drive a small screw or pin into the center of the sacrificial board, not into your project. Set the arm length to the radius you want, measured from the center of the pivot to the center of the bit, not the edge of the router base.

Measure the Radius Correctly

Use a tape or a square to measure from the pivot pin to the outer edge of the bit at its cutting diameter. If you want a 12-inch diameter circle with a 1/2-inch straight bit, your pivot-to-bit-center distance is 6 inches minus half the bit diameter is not needed. Simply measure pivot to bit center: 6 inches for a 12-inch cut. Double-check by rotating the router by hand before power is on.

Choose the Right Bit and Router

A straight router bit with a diameter of 1/4 inch or 1/2 inch works well for most circles. Carbide spiral upcut bits clear chips efficiently, and downcut spirals leave a cleaner top surface on plywood and veneered stock. Use a fixed-base or plunge router with enough power to handle the bit without bogging down. For a deeper look at bit options, see Router Bit for Cutting Circles in Wood: 5 Best Picks Compared (2026). For a deeper look, Best Wood Routers for Woodworking covers this in detail.

Cut the Circle in Passes

  1. Clamp the workpiece firmly to the bench, with the sacrificial board underneath it.
  2. Set the bit depth to no more than 1/8 inch for the first pass in hardwood.
  3. Start the router with the bit outside the cut line, then plunge slowly into the wood.
  4. Rotate the router clockwise around the pivot, keeping steady pressure.
  5. Repeat the full circle, increasing depth by 1/8 inch per pass until you cut through.
  6. Leave a small amount of material for a final light pass to smooth the edge.

For a step-by-step walkthrough of this method with more detail on depth control, read How to Cut a Circle in Wood with Router: Step-by-Step Method (2026).

Finish the Edge and Clean Up

Once the circle is free, the edge may show slight chatter marks. Run a final pass at 1/16 inch depth with a sharp bit, moving at a steady speed. Sand lightly with 150-grit paper to blend the edge. If you are working with a cutout that will be used as a tabletop, consider a roundover bit on the top edge after the circle is complete.

Common Mistakes

  • Plunging too deep on the first pass, which causes burning and tear-out.
  • Measuring the radius to the router edge instead of the bit center.
  • Cutting against the rotation direction, which pulls the router off the path.
  • Letting the pivot pin loosen during the cut, creating an oval.
  • Skipping the sacrificial board, leaving the bottom of the project torn out.
  • A trammel or circle-cutting jig gives you a fixed pivot and repeatable radius. View on Amazon
  • Spiral upcut carbide straight bits clear chips quickly in hardwood and plywood. View on Amazon
  • A pair of clamps keeps the workpiece and sacrificial board from shifting. View on Amazon

FAQ

What is the best bit for cutting wood circles with router?

A carbide straight bit or spiral upcut bit in 1/4 or 1/2 inch diameter works for most jobs. Choose a downcut spiral if you need a clean top surface on plywood.

How deep should each pass be?

Limit each pass to about 1/8 inch in hardwood and up to 1/4 inch in softer stock. Shallow passes reduce burning and protect the pivot setup.

Can I cut a circle without a jig?

You can use a template and a guide bushing, but a trammel jig gives more flexibility for changing diameters. Always test your setup on scrap before cutting the final piece.

Conclusion

Cutting wood circles with router comes down to a secure pivot, accurate radius measurement and shallow, steady passes. Once you have the setup right, you can produce tabletops, shelves and birdhouse parts with clean, repeatable edges. Practice on scrap first, and take your time on the final pass.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.