Updated November 2026

Double decker birdhouse plans give you a two-story nest box with two separate compartments, so two pairs of small birds can nest on the same pole without sharing a cavity. This guide walks through a simple cedar build: the cut list, the entry hole sizes, the assembly order, and the finishing details that keep the birds safe and the box dry. Plan on one weekend and basic hand or power tools.

Cut List and Materials

Use 3/4-inch cedar or another rot-resistant board with rough or lightly textured interior faces, which give young birds grip when they climb out. Cut the pieces below from a single 1×6 and a 1×8 board, leaving a 1/8-inch kerf allowance on each cut.

Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).

  • Two side panels, 7-1/2 in. x 12 in. (upper and lower story share one long wall)
  • Two front and back panels, 6 in. x 12 in. each, one with a 1-1/2 in. entry hole for the lower story
  • Two floor panels, 5-1/4 in. x 5-1/4 in. (one per story)
  • One center divider, 5-1/4 in. x 6 in., with a 1-1/8 in. hole (upper-story entry)
  • One roof panel, 8 in. x 8 in., plus one 1-inch-thick spacer block

Cut and Drill the Pieces

Cut every piece square, then drill the entry holes before assembly. Drill the lower-story hole at 1-1/2 inches, which suits many wrens and chickadees, and the upper-story hole at 1-1/8 inches for smaller species. Center each hole 7 inches above the floor of its own compartment, and drill three or four 1/4-inch ventilation holes near the top of each side. Roughen the interior faces of the front and back panels with a few passes of a file or the coarse side of a sanding block, but leave the outside smooth.

Assemble the Two Stories

Build the lower story first. Glue and screw the floor to the bottom of the side panels, then attach the front and back. Use exterior wood glue and two 1-1/4-inch galvanized or stainless exterior screws per joint. Next, fasten the center divider horizontally at the midpoint, which creates the floor of the upper compartment. Drill pilot holes first to prevent splitting the cedar. Add the upper floor the same way, then check that both compartments are square before the glue sets.

  1. Glue the lower floor to the side panels and drive screws through the sides.
  2. Attach the front and back panels, keeping the entry hole aligned.
  3. Fix the center divider at the midpoint, forming a solid floor for the upper compartment.
  4. Add the upper front and back panels with the second entry hole.
  5. Screw the roof on with the spacer block so it overhangs about 1 inch on each side.

Mount and Maintain the Box

Mount the box on a pole or wall with the entry holes facing away from prevailing winds, ideally facing east or southeast. Keep it 5 to 10 feet above ground, and add a stovepipe baffle if predators are a concern. Clean out old nesting material once a year in late summer, after the birds have fledged.

Common Mistakes

  • Skipping the ventilation holes, which lets heat and moisture build up inside.
  • Making the entry holes too large, which invites starlings and sparrows that compete with native species.
  • Leaving the floor without drainage gaps, so water pools after rain. Drill a few 1/4-inch holes in each floor.
  • Painting or staining the interior, which can release fumes and is unnecessary on untreated cedar.
  • Driving screws without pilot holes, which splits the boards near the ends.

A Forstner bit set makes clean entry holes in cedar without tearing the edges, which helps keep the openings smooth for the birds. Look for: View on Amazon.

A spade bit or a hole saw in the right size is useful for ventilation holes if you prefer not to use a hand drill. Look for: View on Amazon.

Exterior-rated wood glue holds up to rain and temperature changes better than standard glue. Look for: View on Amazon.

FAQ

What hole size should I use for a double decker birdhouse?

Use 1-1/2 inches for the lower story and 1-1/8 inches for the upper story. These sizes suit common wrens and chickadees and help keep larger birds out.

Can I use pressure-treated lumber for these plans?

Avoid it. Chemical treatments can harm nesting birds, so stick with untreated cedar or pine that you seal only on the outside.

How far apart should the two compartments be?

The center divider separates them directly, so the two families never share a cavity. Keep the entry holes on different faces if you can, to reduce traffic between them.

Conclusion

With the cut list, hole sizes, and assembly order above, you can build a sturdy two-story nest box in a weekend. Mount it properly and clean it once a year, and it can host two nesting pairs each season. For more single-chamber options, see Wren Birdhouse Plans PDF: A Step-by-Step Build With Cut List or Simple Cedar Birdhouse Plans: A Step-by-Step Build in One Weekend.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.