Updated November 2026

Travel trailer birdhouse plans give you a nest box shaped like a small camper, with a rounded roof, a rectangular body, and a single round entry hole. You can build one in a weekend using cedar or pine, and the design works well as a decorative piece that still meets the basic needs of cavity-nesting birds like chickadees and wrens. This guide covers the cut list, assembly order, and the details that keep the box safe and usable.

Gather Materials and Cut the Parts

Start with 3/4-inch cedar or untreated pine boards, roughly 5 1/2 inches wide. Cedar resists rot better, but either wood works if you seal the exterior. Use this cut list for a box about 6 inches wide, 6 inches deep, and 10 inches tall at the ridge:

  • Two side walls: 6 in. wide x 8 in. tall at the high edge, angled to meet the roof
  • Front and back: 6 in. wide x 9 in. tall (front gets the entry hole)
  • Floor: 5 1/2 in. x 5 1/2 in.
  • Roof: two panels, each 7 in. x 6 1/2 in., cut so they overhang 1/2 inch at the peak
  • Roof cap or trim strip: 1 in. x 6 in., optional, for a camper-style rooftop detail

Mark the entry hole on the front panel after assembly. Keep the cut edges square, because gaps in the joints let rain and drafts in.

Assemble the Walls and Floor

Dry-fit the sides, front, and back around the floor before adding any glue. Drill pilot holes to prevent splitting, then attach the floor with exterior wood glue and 1 1/4-inch galvanized or stainless screws. Leave the floor slightly inset so water runs off rather than pooling at the seam.

Next, build the roof frame using the two angled panels. A simple butt joint with screws works for a birdhouse, though a rabbet joint at the ridge sheds water more reliably. Drill two or three 1/8-inch drainage holes in the floor and a ventilation slot near the top of each side if you live in a hot climate.

Set the Entry Hole and Mounting Height

Drill the entry hole through the front panel, about 6 inches above the floor. Use the hole size that matches your target species: 1 1/8 inches for chickadees and tufted titmice, and 1 1/4 inches for bluebirds. Smaller holes keep out starlings and house sparrows, which compete aggressively for nest sites.

Mount the box 5 to 10 feet off the ground on a post or fence line, facing away from prevailing winds and afternoon sun. Avoid placing it near bird feeders, since busy traffic can stress nesting pairs. Add a metal predator guard below the box if raccoons or cats are common in your area.

Finish the Exterior and Hang the Box

Sand the exterior smooth, then apply a water-based exterior stain or primer in a light color. Light colors keep the interior cooler. Do not paint or stain the inside, since fumes can harm nestlings. Once dry, attach a hanging bracket or mounting plate to the back, and check that the box sits level so eggs do not roll toward the entry.

Common Mistakes

  • Using pressure-treated lumber, whose chemicals may harm birds.
  • Skipping drainage holes, which leads to damp nests and mold.
  • Making the entry hole too large, which invites predators and competing species.
  • Installing the box in full sun, where interior temperatures climb quickly.
  • Cleaning out old nests too late. Clear the box between breeding seasons.
  • Hole saw set for 1 1/8-inch and 1 1/4-inch openings: a clean-cut entry hole prevents splintering that can injure birds. View on Amazon
  • Exterior wood glue: a waterproof glue keeps joints tight through seasonal swings in humidity. View on Amazon
  • Stainless steel exterior screws: they resist rust and will not stain cedar the way plain steel can. View on Amazon

If you enjoy building small structures, these projects use similar joinery and cuts. Try the Simple Cedar Birdhouse Plans: A Step-by-Step Build in One Weekend for another weekend project, or compare options in 3 Best Free Travel Trailer Birdhouse Plans for Beginners (2026). For a different roof style, see Round Birdhouse Plans Free: A Step-by-Step Build for Beginners.

FAQ

What wood is best for travel trailer birdhouse plans?

Cedar is the most common choice because it resists rot and holds up outdoors without chemical treatment. Untreated pine also works if you seal the exterior with a bird-safe finish.

What entry hole size should I use?

Use 1 1/8 inches for chickadees and titmice, and 1 1/4 inches for bluebirds. Keeping the hole small helps exclude larger competing birds.

How high should the box be mounted?

Mount it 5 to 10 feet off the ground, facing away from strong sun and prevailing wind. Adding a predator guard helps if raccoons or cats visit your yard.

Conclusion

With a basic cut list, careful assembly, and the right entry hole size, you can build a travel trailer birdhouse in a single weekend. Focus on drainage, untreated wood, and safe mounting, and the box should serve birds for many seasons. Clean it out after each nesting season to keep it ready for the next pair.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our woodworking guides, checking product details against manufacturer specifications and owner feedback.