Updated November 2026
A standard handheld router can cut wood up to roughly 2 to 3 inches thick in a single pass, but the real answer depends on your bit length, your router’s motor, and how much material you remove at once. Most people get clean results by making several shallow passes instead of one deep cut. Stock thicker than about 3 inches usually calls for a plunge router, a table, or a different tool altogether.
Why bit length sets the limit
The first number to check is the cutting length of the bit, not the overall length. A straight bit with a 1-1/4 inch cutting edge can’t reliably cut more than about 1-1/4 inch in one pass, no matter how powerful the motor is. Long-reach bits, often sold as 2-inch or 3-inch cutters, extend the usable depth but flex more, and that flex produces chatter, burn marks and uneven walls. Manufacturers typically specify a maximum depth of cut for each bit, and that number should be your starting point.
Shopping for one? See our guide: 7 Best Router Bit to Cut Wood Options for Every Project (2026).
Shank length matters too. The shank must sit deep enough in the collet to hold firmly, and most manufacturers recommend at least 1/2 inch of shank engagement. Pushing a bit to its maximum reach with a short shank is a common cause of slippage.
Factors that change what your router can handle
Motor power and speed control both affect thickness. A router rated around 2 horsepower or more will bog down less when taking a full-depth pass in hardwood. Variable speed lets you slow the bit for large-diameter cutters, which reduces heat and burning. Wood species matters as well: dense hardwoods like oak or maple demand more force per pass than pine or poplar. If you want more background, see How to Make Basic Cuts Safely with a Circular Saw.
Plunge bases and fixed bases behave differently. A plunge router lets you start a cut partway through the material, which is safer for deep dados and mortises. A fixed-base router is generally better for edge work and for guided cuts with a template or fence.
How to cut thick stock safely
For stock thicker than your bit’s comfortable single-pass depth, follow these steps:
- Set the first pass at no more than one-third to one-half of the bit diameter, or about 1/8 to 1/4 inch for most straight bits.
- Make successive passes, increasing depth by similar increments until you reach the full depth.
- Feed against the rotation of the bit (climb cutting is risky and should be avoided on deep passes), following the direction rules your router manual describes.
- Let the bit cool between passes on long cuts, and clear chips so they don’t pack into the flutes.
- Check the bit and collet for wobble before taking deep passes. A loose collet is a common source of ruined work.
Always wear eye and hearing protection, secure the workpiece with clamps, and keep your hands clear of the bit path. If you’re unsure whether your setup can handle a particular depth, consult your router’s manual or a qualified woodworking instructor before proceeding.
What we’d use
For deep, controlled cuts in thick stock, a plunge router gives you the depth adjustment and the start-anywhere ability that fixed bases lack. View on Amazon is a widely known example of this type of tool.
For repeatable multi-pass work on thick panels, a router table with a fence keeps the stock steady across several depth settings. View on Amazon is one option among several accessories that help with this kind of setup.
FAQ
Can a router cut 4-inch thick wood?
Usually not in one pass. Most routers and standard bits are better suited to material up to about 2 to 3 inches. For 4-inch stock, work from both faces, use multiple passes, or switch to a bandsaw or table saw for the initial cut.
Is it better to make one deep pass or several shallow ones?
Several shallow passes are almost always better. They reduce strain on the motor, lower the risk of tearout and burning, and give you a cleaner final surface.
Do I need a plunge router for thick wood?
Not always, but a plunge base makes it much easier to start deep cuts safely and control depth precisely. For edge work or template routing on thinner stock, a fixed base is often sufficient.
Related reading
- Wood Thread Cutting Router Bit: How to Cut Threads in Wood with a Router
- How to Cut a Circle in Wood with Router: Step-by-Step Method (2026)
- How to Cut Wood with a Router: A Step-by-Step Guide for Clean Results
- How to Cut Grooves in Wood with a Router: A Step-by-Step Guide
- How to Cut Curves in Wood with a Router: A Step-by-Step Guide
