Updated November 2026
Simple birdhouse plans for wrens give you a small, sturdy nest box built from one 1×6 board, a few screws, and a handful of cuts. Wrens are small cavity nesters that prefer a snug entrance and a box with a little depth, so the dimensions matter more than decoration. This guide gives you the cut list, the assembly order, and the details that keep wrens nesting and keep the box in good shape for years.
Cut List and Materials
Use untreated pine, cedar, or cypress at about 3/4 inch thick. Cedar resists rot without paint, and untreated wood is safer for birds than chemically treated lumber. A single 6-foot 1×6 board covers every piece below with room to spare.
Shopping for one? See our guide: 5 Best Birdhouses with License Plate Roof Plans for Backyard Builders (2026).
- Front: 1 piece, 4 3/4 in. wide x 9 in. tall (entrance hole goes here)
- Back: 1 piece, 4 3/4 in. wide x 12 in. tall
- Sides: 2 pieces, 4 1/2 in. wide x 9 in. tall, with the top edge cut at a slope so the back stands taller than the front
- Floor: 1 piece, 4 in. x 4 in.
- Roof: 1 piece, 6 in. x 6 in. (overhangs the box on all sides)
How to Cut and Drill the Parts
Cut each piece to size on a table saw or with a circular saw and a straightedge. Check that the two sides match, since uneven sides throw off the roof. Next, drill the entrance hole in the front board. Wrens do best with a hole about 1 1/8 inches in diameter, measured from the top of the box to the center of the hole so it sits roughly 6 inches above the floor.
Drill four 1/4-inch ventilation holes near the top of the sides and a few 1/4-inch drainage holes in the floor. Score the inside face of the front board below the entrance lightly with a saw kerf or scratch lines so chicks can climb out when they fledge.
Assembling the Birdhouse
Attach the floor and sides
Set the floor flat and stand one side on each edge, flush with the floor’s outer edges. Use two 1 5/8-inch exterior screws per side. Pre-drill to prevent splitting, especially on cedar.
Add the front and back
Attach the back first, then the front. Keep the front board slightly proud of the sides only if you want a ledge; otherwise keep everything flush. The sloped sides should leave the back a few inches taller than the front, which lets the roof shed rain.
Fit the roof
Screw the roof on with two screws, leaving it hinged or removable if you want to clean the box after nesting season. Removable roofs make cleanout much easier.
Mounting and Placement
| Factor | Recommended setting |
|---|---|
| Height above ground | 5 to 10 feet |
| Entrance direction | Facing away from prevailing wind and direct afternoon sun |
| Nearby cover | Shrubs or brush within 30 feet, but not directly blocking the entrance |
| Mounting | Fasten to a post or fence with a single nail or screw through the back board |
Avoid placing the box near feeders, which attract predators and competing birds. A quiet corner of a yard with some low cover tends to attract wrens faster.
Common Mistakes
- Using an entrance hole much larger than 1 1/8 inches, which lets in starlings and sparrows that push wrens out.
- Skipping drainage holes, so moisture pools in the floor and chills nestlings.
- Painting the inside or using treated wood, both of which can harm birds.
- Mounting the box too low, where cats and raccoons can reach it.
- Leaving the roof fixed, which makes annual cleaning difficult.
Recommended Gear
A sharp hole saw sized for 1 1/8-inch holes gives a clean entrance without tearout. Look for a Forstner bit set if you prefer a flat-bottomed hole that starts cleanly on thin stock.
Exterior-rated deck screws resist rust and hold cedar well. Choose stainless or coated screws to avoid black staining on the wood. View on Amazon
A combination square helps you mark the 1/4-inch ventilation holes and the entrance hole placement accurately before drilling. View on Amazon
If you want more variations once you have built this design, the Wren Birdhouse Plans PDF: A Step-by-Step Build With Cut List and Carolina Wren Birdhouse Plans: A Step-by-Step Build Guide cover slightly different proportions and mounting options. For a similar scale but a different species, see Tufted Titmouse Birdhouse Plans: A Step-by-Step Build Guide.
FAQ
What size entrance hole do wrens need?
A hole about 1 1/8 inches in diameter works well for most wrens and keeps out larger birds like starlings. Smaller holes can exclude wrens entirely, so avoid going much below that size.
How high should I mount a wren birdhouse?
Aim for 5 to 10 feet above the ground. That height deters most ground predators while keeping the entrance easy for wrens to reach.
Do wren houses need a perch?
No. Wrens do not need a perch, and adding one can give predators an easy foothold. Skip the perch and keep the entrance clean.
Conclusion
With one board, a drill, and a few exterior screws, you can build a wren house that meets the dimensions these birds prefer. Mount it in a quiet spot with some nearby cover, and check it after nesting season. A small, well-placed box often gets used within the first season.
